GE Interlogix 60-792-01-95R User Manual (English)

Other manuals for GE Interlogix 60-792-01-95R

Questions and Answers:

U
ushawSep 1, 2025
Why is my GE Interlogix 60-792-01-95R not reporting to the central station?
- H
  Heather FreemanSep 1, 2025
  If your GE Interlogix Security System's central station or pager is not receiving reports, verify the following: 1. Confirm that the premises phone line is functioning correctly. 2. Perform a phone test to ensure connectivity. 3. Check that the DB-8 cord is securely plugged into the RJ-31X/CA-38A jack. 4. Ensure the DB-8 cord is correctly wired to the panel. 5. Verify the phone line wiring between the TELCO block and RJ-31X/CA-38A jack is accurate. 6. Replace the RJ-31X/CA-38A jack if it is faulty. 7. Replace the DB-8 cord if it is faulty. 8. Confirm that the central station or pager phone number is correctly programmed into the panel. 9. Reprogram the phone number and retest if necessary. 10. Ensure that the correct phone format (SIA or CID) is being used.
R
robertsonaudreyAug 31, 2025
Why does my GE Interlogix 60-792-01-95R display all asterisks?
- B
  bakerstevenAug 31, 2025
  If the display of your GE Interlogix Security System shows all asterisks (************), it means the touchpad is either not connected to the panel bus terminals or is incorrectly wired. Inspect the wiring and correct it as needed.
M
mendozajosephAug 30, 2025
Why does my GE Interlogix Security System say invalid when bypassing a sensor?
- K
  Kenneth FlowersAug 30, 2025
  If your GE Interlogix Security System touchpad displays 'Invalid' or you hear 'Invalid' when trying to bypass a sensor, it could be due to: 1. Attempting to bypass a 24-hour sensor (group 26 fire sensors), which cannot be bypassed. 2. The sensor not being active in the current arming level. The system will automatically cancel sensor bypass when you attempt to arm to level 2 or 3.
M
Micheal RiveraAug 29, 2025
Why doesn't my GE Interlogix 60-792-01-95R Security System go into alarm when zone is tripped?
- C
  christophergrayAug 29, 2025
  If your GE Interlogix Security System is not triggering an alarm when a zone is tripped, consider the following: 1. Ensure the system is armed before testing the zone. 2. Verify the zone is correctly learned into the panel's memory via the installer/dealer program mode under LEARN SENSORS. 3. Check if the zone is assigned to the correct partition. If not, either delete it and relearn it into the correct partition, or modify the partition setting in the EDIT SENSORS menu. 4. For HIM zones, confirm that the HIM LED is blinking, which indicates communication with the panel.
S
Shannon MillsAug 28, 2025
Why does my GE Interlogix 60-792-01-95R Security System protest and won't arm?
- E
  Elizabeth AlvarezAug 28, 2025
  If your GE Interlogix Security System protests and refuses to arm: 1. When arming to level 2, ensure all monitored perimeter doors and windows are fully closed. 2. If arming to level 3, verify that all perimeter and interior sensors are closed. 3. Press the STATUS button to see an indication of the specific problem.
R
Robert MillsAug 28, 2025
Why won't my GE Interlogix Security System disarm?
- N
  nhaleAug 28, 2025
  To address a GE Interlogix Security System that won’t disarm: 1. Ensure the correct access code is being used. 2. Verify the access code is programmed and authorized to disarm the system in user programming. 3. Check if a wireless touchpad is properly connected to the system, or if a hardwired touchpad is communicating with the panel. Refer to installer programming for wireless touchpad setup. 4. Avoid using the installer code to disarm the system; it is designed not to function for disarming. Use a regular or system master code instead.
D
David BanksAug 27, 2025
What to do if there's no AC voltage at my GE Interlogix Security System panel terminals?
- J
  jamiejohnstonAug 27, 2025
  To resolve a lack of incoming AC voltage at panel terminals 1 and 2 of your GE Interlogix Security System: 1. Unplug the AC power transformer and disconnect the wires from both the transformer and the panel. 2. Inspect the wiring between the transformer and the panel for any shorts or open circuits. 3. Plug in the transformer and check for 24 VAC at the unconnected terminals. If there's no voltage, replace the transformer.
T
Tami BaileyAug 26, 2025
What does it mean when my GE Interlogix 60-792-01-95R Security System says 'Sensor low battery'?
- K
  Kelly GordonAug 27, 2025
  If your GE Interlogix Security System indicates a 'Sensor/Touchpad nn low battery', replace the battery in the device indicated. After replacing the battery, test the sensor or touchpad.
R
rjohnsonAug 25, 2025
What to do if GE Interlogix 60-792-01-95R shows AC power failure?
- J
  Jennifer KellyAug 26, 2025
  If, after pressing the STATUS button on your GE Interlogix Security System touchpads, you see 'AC' flashing or 'AC Power Failure/AC Failure' displayed (while the panel continues running on backup battery), take these steps: 1. Verify that the AC circuit breaker is on to ensure the circuit is live. 2. Inspect the wiring between the panel and transformer for any issues. 3. Confirm that the transformer is plugged into an outlet that is not controlled by a switch and is secured with the provided screw. 4. Ensure the transformer is supplying AC power to the panel.
C
Christopher ClarkAug 25, 2025
How to troubleshoot GE Interlogix Security System when panel doesn't power up?
- M
  Ms. Tammy SanchezAug 25, 2025
  If your GE Interlogix Security System panel does not power up and the touchpads remain blank or unresponsive, follow these steps: 1. Ensure the panel transformer is plugged into an outlet that is not controlled by a switch. 2. Verify the AC circuit breaker to confirm the circuit is active. 3. Confirm that the backup battery is correctly installed and that the AC power transformer is properly connected. 4. Inspect the wiring of both the panel and transformer for any issues. 5. Measure the incoming AC voltage at panel terminals 1 and 2, which should read approximately 24 VAC.