GE Interlogix Concord Security System User Manual

Concord 46
The following sections describe the settings that appear under REPORTING—PARTITION 1-2.
Program Report (06015)
Reporting-Global (Default = off)
When this setting is on, the panel sends a report to the central sta-
tion when someone enters or exits installer programming.
¾
To turn Program Report on or off:
1. With the display showing PROGRAM REPORT ON/
OFF
(current setting), press 1 (off) or 2 (on). The
display flashes the entered setting.
2. Press # and the display shows the new setting.
Opening Reports (partition 1: 06100, partition 2: 06200)
Reporting-Partition 1-2 (Default = off)
When this setting is on, the panel sends an opening report to the central
station after disarming the system.
Note
To use this feature, the Open/Close Reports settings under the
PHONES
menu must be turned on for the specific CS Phone or Pager number.
¾To turn Opening Reports off or on:
1. With the display showing OPENING REPORTS
OFF/ON
(current setting), press 1 (off) or 2 (on).
The display flashes the entered setting.
2. Press # and the display shows the new setting.
Closing Reports (partition 1: 06101, partition 2: 06201)
Reporting-Partition 1-2 (Default = off)
When this setting is on, the panel sends a closing report to the central
station after arming the system.
Note
To use this feature, the Open/Close Reports settings under the
PHONES
menu must be turned on for the specific CS Phone or Pager number.
¾To turn Closing Reports off or on:
1. With the display showing CLOSING REPORTS
OFF/ON
(current setting), press 1 (off) or 2 (on).
The display flashes the entered setting.
2. Press # and the display shows the new setting.
Recent Closings (partition 1: 06102, partition 2: 06202)
Reporting-Partition 1-2 (Default = on)
When this setting is on, the panel sends a recent closing report to the
central station if an alarm occurs within two minutes after the exit
delay time expires. Such a report is used to identify a possible exit
fault.
¾
To turn Recent Closings off or on:
1. With the display showing RECENT CLOSINGS
OFF/ON
(current setting), press 1 (off) or 2 (on).
The display flashes the entered setting.
2. Press # and the display shows the new setting.
No Activity (partition 1: 06103, partition 2: 06203)
Reporting-Partition 1-2 (Default = off)
When this setting is on, the panel sends a no activity report to the cen-
tral station when the activity timeout expires (see
TIMERS—ACTIVITY TIM-
EOUT).
¾
To turn No Activity reports off or on:
1. With the display showing NO ACTIVITY OFF/ON
(current setting), press 1 (off) or 2 (on). The dis-
play flashes the entered setting.
2. Press # and the display shows the new setting.
Duress Option (partition 1: 06104, partition 2: 06204)
Reporting-Partition 1-2 (Default = off)
(Default = off) When this setting is on, the system can be controlled
using a programmed duress code (see
SECURITY—PARTITION N—DURESS
CODE
).
Note
For UL Listed installations, Duress Option must be set to off.
Do not use a duress code unless it is absolutely necessary. Using duress
codes often results in false alarms due to code entry errors. If a duress
code is absolutely necessary, use it with the audio verification module
to reduce false alarms and accidental dispatches.
¾
To turn Duress Option off or on:
1. With the display showing DURESS OFF/ON (cur-
rent setting), press 1 (off) or 2 (on). The display
flashes the entered setting.
2. Press # and the display shows the new setting.

GE Interlogix Concord Security System Specifications

General

Brand	GE Interlogix
Model	Concord Security System
Category	Security System
Language	English