GE F35 - Page 677

INDEX
F35 MULTIPLE FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL xi
Real power specifications ...............................................................2-24
Real-time clock
actual values for synchronization .............................................. 6-8
settings ...............................................................................................5-146
Reboot relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Recloser curves ...................................................................5-199, 5-233
Redundancy
PRP actual values .............................................................................6-11
PRP explained .....................................................................................5-46
settings ..................................................................................................5-44
specifications ......................................................................................2-30
Relay architecture ............................................................................5-203
Relay maintenance ............................................................................... 7-3
Relay name ..........................................................................................5-179
Release Notes .....................................................................................10-14
Remote access of front panel in EnerVista ................. 4-17, 6-3
Remote access, explained ................................................................ 5-8
Remote Setting Authorization ...................................................10-14
Repair ...................................................................................1-2, 10-29, D-1
Replace battery .................................................................................10-24
Replace battery message .................................................................7-7
Replace front panel .........................................................................10-15
Replacement modules ......................................................................2-13
Requirements for installation .......................................................3-52
Reset to factory defaults ....................................................... 5-7, 5-21
Resetting
FlexLogic operands .......................................................................5-214
setting to clear LEDs and messages ....................................5-315
to factory defaults .............................................................................. 5-7
Restart relay
using EnerVista .................................................................................... 5-1
using relay .............................................................................................. 7-3
Restore settings ....................................................................................10-8
Revision history .......................................................................................D-1
RF immunity specifications ............................................................2-33
RFI, conducted specifications .......................................................2-33
R-GOOSE description ..........................................................5-64, 5-102
RJ-45 ................................................................................................. 2-6, 3-11
RMS voltage specifications ............................................................2-24
Roles for login ..........................................................................................2-4
Rolling demand ..................................................................................5-157
Routable GOOSE ....................................................................5-64, 5-102
RS232
baud rate ..............................................................................................5-41
configuration ......................................................................................3-64
specifications ......................................................................................2-29
wiring ......................................................................................................3-29
RS422
configuration ......................................................................................3-41
timing .....................................................................................................3-42
two-channel application ...............................................................3-41
with fiber interface ...........................................................................3-43
RS485
description ........................................................................................... 3-31
port on rear panel ............................................................................3-11
settings .................................................................................................5-41
specifications .....................................................................................2-29
RTD FlexAnalogs ..................................................................................A-35
RTD inputs
actual values ......................................................................................6-23
settings ...............................................................................................5-323
specifications .....................................................................................2-26
Rules for passwords .............................................................................5-8
RxGOOSE
actual values ......................................................................................6-22
error messages ....................................................................................7-9
FlexAnalogs .........................................................................................A-36
settings ...................................................................................5-69, 5-107
S
Save settings ............................................................................................4-1
Saving setting does not take relay out of service ...............5-1
SCADA protocol selection ...............................................................5-50
SCD file
import ..................................................................................................10-12
import preferences ..........................................................................10-9
SCL compatible ........................................................................5-56, 5-93
SCL file import ...................5-73, 5-75, 5-76, 5-111, 5-113, 5-114
preferences .........................................................................................10-9
Security
commands .............................................................................................7-4
delete files and records ...............................................................10-29
EnerVista and UR secure with SSH .............................................2-3
failed authentication lockout .....................................................5-21
forceful user logout ............................................................................7-3
lock FlexLogic equations .................................................................4-9
password for settings template ...................................................4-7
passwords for settings and commands ..........4-61, 5-9, 5-10
RADIUS server for user authentication .....................................B-1
role-based user access ....................................................................2-4
settings .................................................................................................5-19
software options ..............................................................................2-31
specifications .....................................................................................2-31
system and event logs ...................................................................5-24
Security audit list of port numbers ........................................... 5-44
Selector switch
actual values .........................................................................................6-7
application example .....................................................................5-264
FlexLogic operands .......................................................................5-210
logic diagram ...................................................................................5-266
settings ...............................................................................................5-259
specifications .....................................................................................2-22
timing ...................................................................................................5-263
Self-tests
description ..............................................................................................7-6
error messages ....................................................................................7-6
FlexLogic operands .......................................................................5-214
user-programmable .....................................................................5-161