Graco PrecisionSwirl - Page 33

Graco PrecisionSwirl

150 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Installation

3A2098S 33

FIG. 20: Cable Installation Diagram

ti30855a

Multiple Fluid Plate and Multiple Swirl System shown

4

5

4

4

3

1

1

2

2

2

2

1

Table of Contents

Default Chapter2
- Table of Contents2
Related Manuals3
Models4
- Fluid Plate Kits5
- Control Panel Kits7
- Expansion Swirl Enclosure Assemblies8
- Precisionswirl Orbital Dispenser Assemblies8
- Automation Gateway Assemblies9
- Swirl Control DGM9
- Integration Upgrade with Advanced Map10
Warnings11
System Configurations13
- Typical Installation - Single Swirl, Single Fluid Plate13
- Typical Installation - Multiple Fluid Plates, no Swirl Dispensers14
- Typical Installation - Multiple Fluid Plates, Multiple Swirl Dispensers15
Overview16
- System Overview16
- System Components16
- Fluid Plate Assembly Overview17
- Control Center Assembly Overview19
- Key Tokens23
Installation24
- Before Installation24
- Overview24
- Install Control Center25
- Install Fluid Plate Assemblies27
- Install Cable Assemblies32
- Install Gateway Module Interface34
System Setup36
- Overview36
- Configure System36
- Configure Control Settings37
- Configure Mode Settings38
- Configure Delay Settings38
- Configure Flow Meter Settings39
- Configure Pressure Loop Settings39
- Adjust Pressure Sensors40
- Configure Errors40
- Setup Maintenance Schedule/Parameters41
- Configure Valve to Swirl Association and Motor Error Type41
- Configure Swirl Settings42
- Configure Gateway Settings42
- Setup Styles42
- Configure Advanced Settings42
- On/Off Delays43
Operation44
- Startup44
- Load Material44
- Maintenance Mode Operation45
- Automation Control (Normal Operation)49
- Jobs49
- Styles50
- Precharge Modes51
- Typical Job Cycle53
Pressure Relief Procedure61
Shutdown62
USB Data63
- USB Logs63
- System Configuration Settings File64
- Custom Language File64
- Download Procedure65
- Upload Procedure65
Troubleshooting66
- Fluid Plates66
- Flow Meter67
- Fluid Regulator67
- Dispense Valves68
- Gateway Module69
- LED Diagnostic Information69
Errors70
- View Errors70
- Diagnose Errors70
- Event and Error Codes and Troubleshooting71
Maintenance80
- Maintenance Schedule80
- Advanced Display Module (ADM)81
- Upgrade Gateway Module Software (16K743)81
- Upgrade Gateway Module Fieldbus Map82
  - Or 17P799)82
- Upgrade Fluid Control Module (FCM) Software83
  - (16K743)83
- Air Filter Maintenance83
- Swirl Dispensers83
Repair84
- Fluid Plate Assembly84
- Control Center Assembly91
Parts95
- Control Centers95
  - Parts96
- Fluid Plate Assembly Parts98
Appendix A - Advanced Display Module (ADM)104
- Display Overview104
- Display Details104
- Setup Mode106
- Run Mode116
Appendix B - Discrete Gateway Module (DGM) Connection Details121
- D-Sub Cable 123793121
- D-Sub Cable 123792 and Breakout Board 123783122
- DGM Digital Input125
- DGM Digital Outputs126
- DGM Analog Inputs127
- DGM Analog Outputs127
Appendix C - Communications Gateway Module (CGM) Connection Details128
- Install Fieldbus Connections128
- CGM I/O Data Map131
Appendix D - I/O Signal Descriptions146
- Automation Inputs146
- Automation Outputs147
Technical Data148
- Swirl Dispenser Technical Data148
- Fluid Plate Assembly Technical Data149
- Control Center Assembly Technical Data149
Graco Standard Warranty150
Graco Information150

Related product manuals

Preview: Graco PR70

Preview: Graco PR70 Series

Graco PR70 Series

Preview: Graco E-Flo iQ