Graco PrecisionSwirl - Fluid Plate Assembly Parts

Graco PrecisionSwirl

150 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Parts

98 3A2098S

Fluid Plate Assembly Parts

S

101

143

142

152

131

153

151

135, 136

199

117, 120

Table of Contents

Default Chapter2
- Table of Contents2
Related Manuals3
Models4
- Fluid Plate Kits5
- Control Panel Kits7
- Expansion Swirl Enclosure Assemblies8
- Precisionswirl Orbital Dispenser Assemblies8
- Automation Gateway Assemblies9
- Swirl Control DGM9
- Integration Upgrade with Advanced Map10
Warnings11
System Configurations13
- Typical Installation - Single Swirl, Single Fluid Plate13
- Typical Installation - Multiple Fluid Plates, no Swirl Dispensers14
- Typical Installation - Multiple Fluid Plates, Multiple Swirl Dispensers15
Overview16
- System Overview16
- System Components16
- Fluid Plate Assembly Overview17
- Control Center Assembly Overview19
- Key Tokens23
Installation24
- Before Installation24
- Overview24
- Install Control Center25
- Install Fluid Plate Assemblies27
- Install Cable Assemblies32
- Install Gateway Module Interface34
System Setup36
- Overview36
- Configure System36
- Configure Control Settings37
- Configure Mode Settings38
- Configure Delay Settings38
- Configure Flow Meter Settings39
- Configure Pressure Loop Settings39
- Adjust Pressure Sensors40
- Configure Errors40
- Setup Maintenance Schedule/Parameters41
- Configure Valve to Swirl Association and Motor Error Type41
- Configure Swirl Settings42
- Configure Gateway Settings42
- Setup Styles42
- Configure Advanced Settings42
- On/Off Delays43
Operation44
- Startup44
- Load Material44
- Maintenance Mode Operation45
- Automation Control (Normal Operation)49
- Jobs49
- Styles50
- Precharge Modes51
- Typical Job Cycle53
Pressure Relief Procedure61
Shutdown62
USB Data63
- USB Logs63
- System Configuration Settings File64
- Custom Language File64
- Download Procedure65
- Upload Procedure65
Troubleshooting66
- Fluid Plates66
- Flow Meter67
- Fluid Regulator67
- Dispense Valves68
- Gateway Module69
- LED Diagnostic Information69
Errors70
- View Errors70
- Diagnose Errors70
- Event and Error Codes and Troubleshooting71
Maintenance80
- Maintenance Schedule80
- Advanced Display Module (ADM)81
- Upgrade Gateway Module Software (16K743)81
- Upgrade Gateway Module Fieldbus Map82
  - Or 17P799)82
- Upgrade Fluid Control Module (FCM) Software83
  - (16K743)83
- Air Filter Maintenance83
- Swirl Dispensers83
Repair84
- Fluid Plate Assembly84
- Control Center Assembly91
Parts95
- Control Centers95
  - Parts96
- Fluid Plate Assembly Parts98
Appendix A - Advanced Display Module (ADM)104
- Display Overview104
- Display Details104
- Setup Mode106
- Run Mode116
Appendix B - Discrete Gateway Module (DGM) Connection Details121
- D-Sub Cable 123793121
- D-Sub Cable 123792 and Breakout Board 123783122
- DGM Digital Input125
- DGM Digital Outputs126
- DGM Analog Inputs127
- DGM Analog Outputs127
Appendix C - Communications Gateway Module (CGM) Connection Details128
- Install Fieldbus Connections128
- CGM I/O Data Map131
Appendix D - I/O Signal Descriptions146
- Automation Inputs146
- Automation Outputs147
Technical Data148
- Swirl Dispenser Technical Data148
- Fluid Plate Assembly Technical Data149
- Control Center Assembly Technical Data149
Graco Standard Warranty150
Graco Information150

Related product manuals

Preview: Graco PR70

Preview: Graco PR70 Series

Graco PR70 Series

Preview: Graco E-Flo iQ