HEIDENHAIN TNC 320 - Page 463

HEIDENHAIN | TNC 320 | User’s manual for cycle programming | 9/2016
463
Index
3
3D Touch Probes...................... 294
3-D touch probes....................... 42
A
Automatic datum setting.......... 324
At center of 4 holes............... 365
Center of a bolt hole circle..... 360
Center of a circular pocket
(hole)...................................... 342
Center of a circular stud......... 347
Center of a rectangular
pocket.................................... 335
Center of a rectangular stud... 339
In any axis.............................. 369
Inside of corner...................... 356
In the touch probe axis........... 363
Outside of corner................... 351
Ridge center.......................... 332
Slot center............................. 328
Automatic tool measurement... 448
Axis-specific scaling................. 263
B
Back boring................................ 77
Basic rotation
Measure during program run.. 304
Bolt hole circle......................... 177
Bore milling................................ 85
Boring......................................... 71
C
Centering................................... 65
Circular pocket
Roughing+finishing................ 136
Circular point patterns.............. 177
Circular slot
Roughing+finishing................ 146
Circular stud............................. 155
Classification of results............ 379
Compensating workpiece
misalignment............................ 304
By measuring two points on a
straight line............................ 306
Over two circular studs.......... 312
Over two holes...................... 309
Via rotary axis................ 315, 319
Consideration of basic rotation. 294
Contour cycles......................... 186
Contour train.................... 205, 207
Coordinate transformation........ 250
Cycle.......................................... 46
Calling...................................... 48
Define...................................... 47
Cycles and point tables.............. 62
Cylinder surface
Machine contour............ 219, 228
Ridge machining..................... 225
Slot machining........................ 222
D
Datum shift.............................. 251
In the program....................... 251
With datum tables................. 252
Drilling............................ 67, 74, 81
Drilling Cycles............................ 64
Dwell time................................ 275
E
Engraving................................. 282
F
Face milling.............................. 287
FCL function................................ 7
Feature Content Level.................. 7
Floor finishing........................... 200
Fundamentals of Thread
Milling...................................... 104
H
Helical thread drilling/milling..... 118
I
Inside thread milling................. 106
L
Linear point patterns................ 180
M
Machine parameters for 3D touch
probe........................................ 297
Machining pattern...................... 54
Measure angle......................... 384
Measure angle of a plane......... 413
Measure any coordinate........... 407
Measure bolt hole circle........... 410
Measure hole........................... 387
Measure hole inside................. 387
Measure hole outside.............. 391
Measurement parameters........ 379
Measurement results in Q
parameters............................... 379
Measure rectangular pocket..... 398
Measure rectangular stud........ 395
Measure the plane angle.......... 413
Measure the slot width............ 401
Measure the width of a
ridge................................. 404, 404
Measuring slot width............... 401
Measuring the width of a ridge 404
Mirroring................................... 258
O
Outside thread milling.............. 122
P
Pattern definition........................ 54
Peck drilling.......................... 81, 87
Point patterns........................... 176
Overview................................ 176
Point tables................................ 60
Polygon stud............................ 159
Positioning logic....................... 299
Probing feed rate..................... 298
Program call............................. 276
Via cycle................................. 276
R
Reaming..................................... 69
Recording measurement results....
377
Rectangular pocket
Roughing+finishing................ 131
Rectangular stud...................... 151
Rotation.................................... 260
Roughing:See SL Cycles,
Roughing.................................. 196
S
Scaling...................................... 262
Set a basic rotation.................. 318
Side finishing............................ 202
Single-lip deep-hole drilling......... 87
SL Cycles................. 186, 219, 228
Contour cycle......................... 188
Contour data.......................... 192
Contour train.................. 205, 207
Floor finishing......................... 200
SL cycles
Fundamentals......................... 186
Fundamentals......................... 246
SL Cycles
Pilot drilling............................ 194
Roughing................................ 196
Side finishing.......................... 202
Superimposed contours. 189, 240
SL cycles with complex contour
formula..................................... 236
SL cycles with simple contour
formula..................................... 246
Slot milling
Roughing+finishing................ 141
Spindle orientation................... 278
T
Tapping
With a floating tap holder......... 95
With chip breaking................. 100
Without a floating tap
holder............................... 97, 100
Thread drilling/milling............... 114
Thread milling/countersinking... 110
Tilting function