Hirschmann PAT IFLEX5 - System Block Diagram

To Next Page

To Previous Page

Drawings

15.2 BLOCK DIAGRAM

Hirschmann Electronics, Inc. reserves proprietary rights to this drawing and to the data shown there on. The

drawing and data are confidential and are not to be used or reproduced without the written consent of

Hirschmann. This drawing is subject to technical modification without prior notice.

CAN-BUS

RS 485

Serial

Interface

Current

4..20mA

CAN-connector

iflex5 Central Unit

Dual Pressure

Graphic

Console

Length/Angle Sensor

A2B

Switch

Slew Sensor

70 pin

Connector

Crane Power

CAN-connector

Lockout

Main Page

Default Chapter4
- Table of Contents4
1 General Information7
2 Warnings7
3 Description of the System8
- Description of System Function8
- Description of a Can Bus System8
- Description of the System Components9
4 What's Wrong10
- Ihave an Error Code Indicated on the Console10
- The Displayed Angle Does Not Match the Actual Boom Angle10
- The Displayed Length Does Not Match the Actual Boom Length10
- The Displayed Slewing Does Not Match the Actual Slewing Angle10
- The Displayed Load Does Not Match the Actual Load10
- The Console Display Is Blank10
- Ihave an A2B Problem10
- I Havea Can-Bus Problem10
- Ineed to Identify a Spare Part10
5 Angle Sensing11
- Angle Sensing Error - Flow Chart12
6 Length Sensing14
- Length Sensing Error - Flow Chart15
7 Pressure Sensing17
- Pressure Sensing Error - Flow Chart17
8 Slewing Sensing18
- Slew Sensing Error - Flow Chart19
9 Load Sensing20
- Load Sensing Error - Flow Chart20
10 No Console Display21
11 A2B Problem22
12 Cann-Bus Communication23
- E6123
  - E61 - Flow Chart24
- E6225
- E6325
- E6425
  - E64 - Flow Chart26
- E6526
13 Troubleshooting a Sensor Problem Using the Display27
14 Iflex5 Boom Control System (BCS)30
- Rt9000E / Rt800E Basics30
- Tele Sequence32
- Iflex5 Bcs Digital Inputs32
- Rt9000E / Rt800E Iflex5 Bcs Digital Outputs33
- Iflex5 Bcs Analog Inputs and Pwm Outputs35
- Iflex5 Bcs Test Display37
- Boom out of Sequence38
- Tele Rod Drain Valve38
- Tele Two Stage Relief Valve38
- Hydraulic Luffing Boom Extension39
15 Drawings40
- Components of the Lmi System Pat Iflex540
- Block Diagram41
- Electrical System Diagram Standard System42
- Main Central Unit Connector44
- Electrical System Diagram Boom Control System45
16 Spare Part Listings50
- Central Unit, Iflex5 Part No. 021-020-060-00350
- Graphic Console Assy, Vertical Part No. 050-350-061-35651
- Graphic Console Assy, Part No. 050-350-061-37652
- Cable Reel, Lwg508 Part No. 068-508-060-00153
- Cable Reel, Lwg521 Part No. 068-521-060-00255
- Cable Reel, Lwg152 Part No. 067-152-060-05656
- Pressure Transducer Block, Dav314/0014 Part No. 044-314-060-01457
- Cable Assembly 11M, Part No. 031-010-101-00757
- Wiring Harness Standard, Part No. 031-010-100-54957
- Wiring Harness Boom Control, Part No. 031-010-100-55458
- Cable Assembly, 14M Part No. 031-010-100-55558
- Trs05 Repeater, Radio Windspeed Kit 031-300-104-08759
17 Service Screen for Sensor Calibration60
- Activating the Service Screen for Sensor Calibration60
- Zero-Setting the Transducer Inputs61
- Zero-Setting the Slewing Inputs61
- Length Sensor Calibration Procedure62
- Angle Sensor Calibration Procedure65
- Zero-Setting the Slew Potentiometer67
18 Error Codes68
19 Troubleshooting Moisture78
- Water Ingress78
- Condensation79

Hirschmann PAT IFLEX5 - System Block Diagram

Table of Contents

Related product manuals