Honeywell VISTA-128BPT - Deleting a User

17
S
S
E
E
C
C
T
T
I
I
O
O
N
N
:
:
3
3
D
D
A
A
T
T
A
A
F
F
I
I
E
E
L
L
D
D
S
S
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
A
A
b
b
o
o
u
u
t
t
D
D
a
a
t
t
a
a
F
F
i
i
e
e
l
l
d
d
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
The following pages list this control’s data fields in numerical order. Field numbers are listed in the left column, followed
by a “Title and Data Entries column, which lists the valid entries for each field and a third column depicting the defaulted
values. Underneath those columns (for each field) an explanation and additional information are described.
NOTE: All references in this manual for number of zones, number of user codes, number of access cards, and the
event log capacity, use the VISTA-250BPT’s features. All other features are identical.
S
S
U
U
M
M
M
M
A
A
R
R
Y
Y
O
O
F
F
P
P
R
R
O
O
G
G
R
R
A
A
M
M
M
M
I
I
N
N
G
G
C
C
O
O
M
M
M
M
A
A
N
N
D
D
S
S
DESIRED ACTIONS
SYNTAX
To enter program mode
Enter installer code + [8] + [0] + [0] + [0]
To set standard defaults
Press ∗97
To change to next page of program fields
Press
∗
94
To return to previous set of fields
Press ∗99
To erase account and phone number field entries
Press [
∗
] + field number + [
∗
]
To assign zone descriptors
Press #93 + follow menu prompts
To change partitions (for partition specific fields)
Press
∗
91 + desired partition number
To add custom words Press #93 + follow menu prompts
To enter Installer's Message
Press #93 + follow menu prompts
To exit program mode
Press ∗99 OR ∗98:
∗
99 allows re-access to programming mode by installer code.
∗
98 prevents re-access to programming mode by installer
code.
NOTE: If local programming lockout is set via downloading, programming mode cannot be entered at the keypad. In the
event that local programming is required after the lock-out, setting the location in Compass will open a 24-hour
window for programming when the Master code + #65 – command is entered. The 24-hour window counts down
and then locks out local programming until the next Master code + #65-command is entered.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
D
D
a
a
t
t
a
a
F
F
i
i
e
e
l
l
d
d
s
s
Data field programming involves making the appropriate entries for each of the data fields. Start Data Field programming
by entering the installer code + 8 + 0 + 0 + 0.
FIELD TITLE and DATA ENTRIES Default Values
∗
00
INSTALLER CODEA
Enter 4 digits, 0-9
[4112] AAA E E E E
• Only code that can be used to enter the Program Mode.
• Cannot be used to disarm the system if it is not used to arm the system.
• Cannot be used to re-enter Program Mode if it is exited by the ∗98 command.
∗
04
ENABLE RANDOM TIMERS FOR PARTITIONS 1-8
0 = disable
1 = enable
AAA
EEE1EEE
AAAAAA
EEE2EEE
AAA
AAA
EEE3EEE
AAA
AAA
EEE4EEE
AAA
AAA
EEE5EEE
AAA
AAA
EEE6EEE
AAA
AAA
EEE7EEE
AAA
AAA
EEE8EEE
If enabled, the activation time of the window is randomized up to 30 minutes and is initialized by either of two methods:
User Code + [#] + [41]: Initiates the random schedule for all devices in the partition.
User Code + [#] + [42]: Initiates the random schedule for all devices in the partition with a time window within 6 PM and 5
∗
05
SYSTEM EVENTS NOTIFY
0 = disable
1 = enable
[0] AAA E
Field
∗
14 must be set for RS232 port
(1).
NOTES:
• If enabled, the system also sends fault and restore messages via the RS232 port (TB4).
• While in a communication session with Compass, system events will not operate.