SEBU7833-03 25
Operation Section
Lifting and Storage
•
Renew the canis
ter(s) of the lubricating oil filter.
•
FilltheoilpantotheFullMarkonthedipstick
with new, clea
n lubricating oil. Add 1762811
POWERPART Lay-Up 2 to the oil in order to
protect the engine against corrosion. If 1762811
POWERPART La
y-Up 2 is not available, use a
preservative of the correct specification instead
of the lubricating oil. If a preservative is used,
this must be d
rained completely at the end of the
storage period and the oil pan must be refilled to
the correct level with normal lubricating oil.
Cooling System
To help prevent excessive engine wear, use the
following guidelines:
NOTICE
Do not drain the coolant while the engine is still hot and
the system is under pressure because dangerous hot
coolant can
be discharged.
If freezing temperatures are expected, check the
cooling sys
tem for adequate protection against
freezing. See this Operation and Maintenance
Manual, “General Coolant Information” (Maintenance
Section).
NOTICE
To prevent frost damage, ensure that all the coolant is
removed fr
om the engine. This is important if the sys-
tem is drained after it has been flushed with water, or if
an antifreeze solution too weak to protect the system
from frost
has been used.
g010039
28
Illustration 23
1. Ensure that the vehicle is on level ground.
2. Remove t
he filler cap of the cooling system.
3. Remove the drain plug (1) from the side of the
cylinde
r block in order to drain the engine. Ensure
that the drain hole is not restricted.
4. Open the tap or r
emove the drain plug at the
bottom of the radiator in order to drain the radiator.
If the radiator does not have a tap or a drain plug,
disconnect th
e hose at the bottom of the radiator.
5. Flushthecoolingsystemwithcleanwater.
6. Fit the drain plugs and the filler cap. Close the tap
or connect the radiator hose.
7. Fill the cooling system with an approved
antifreeze mixture because this gives protection
against corr
osion. The maximum flow rate is 1 L
(0.2200Impgal)perminuteinordertofill the
system.
Note: Certain corrosion inhibitors could cause
damage to some engine components. Contact the
Service Dep
artment of Perkins for advice.
8. Operate the engine for a short period in order to
circulate t
he lubricating oil and the coolant in the
engine.
9. Disconnect
the battery. Put the battery into safe
storage in a fully charged condition. Before the
battery is put into storage, protect the terminals
against co
rrosion.1734115 POWERPART Lay-Up
3 can be used on the terminals.
10. Clean the c
rankcase breather if one is installed.
Seal the end of the pipe.
11. Remove the
fuel injector nozzles and spray
1762811 POWERPART Lay-Up 2 for one or two
seconds into each cylinder bore with the piston
at BDC.
12. Slowly rotate the crankshaft for one complete
revoluti
on and then replace the fuel injector
nozzles.
Induction System
•
Remove th
eairfilter assembly. If necessary,
remove the pipes that are installed between
the air filter assembly and the turbocharger.
Spray 17
62811 POWERPART Lay-Up 2 into the
turbocharger. The duration of the spray is printed
on the container. Seal the turbocharger with
waterpr
oof tape.
Exhaust
System
•
Remove the exhaust pipe. Spray 1762811
POWERP
ART Lay-Up 2 into the turbocharger. The
duration of the spray is printed on the container.
Seal the turbocharger with waterproof tape.
This document is printed from SPI². Not for Resale.
To Next Page
Loading...
