Icom i9100 User Manual

TABLE OF CONTENTS
vi
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
■ Electronic keyer functions ...............................50
D Memory keyer menu construction ............... 50
D Memory keyer send menu...........................51
D Editing a memory keyer .............................. 52
D Contest number Set mode .......................... 53
D Keyer Set mode .......................................... 54
 ■OperatingRTTY(FSK) .................................... 56
 ■RTTYfunctions................................................ 57
DConstructionofRTTYmenu ....................... 57
DAboutRTTYreversemode .........................58
D Twin Peak Filter ........................................... 58
DRTTYdecoder ............................................. 59
DRTTYSetmode .......................................... 60
 ■ Operating AM/FM ............................................ 61
 ■ Tone squelch operation ................................... 62
 ■ DTCS operation .............................................. 63
 ■ Tone scan/DTCS code scan operation ............ 64
 ■ Repeater operation ......................................... 65
D Repeater access tone frequency setting ..... 65
D One-touch repeater function ....................... 66
D Transmit frequency monitor check...............66
D 1750 Hz tone burst ...................................... 66
D Setting the Auto Repeater ranges
(U.S.A. and Korea versions only) ................ 67
D Turning ON the Auto Repeater function
(U.S.A. and Korea versions only) ................ 68
D Storing a non standard repeater ................ 68
5 FUNCTIONS FOR RECEIVE ........................ 69–77
 ■ AFC operation ................................................. 69
 ■ RIT function ..................................................... 69
D RIT monitor function .................................... 69
 ■ Simple band scope .......................................... 70
 ■ Preamplifier ..................................................... 71
 ■ Attenuator ........................................................ 71
 ■ AGC function ................................................... 72
D AGC speed selection .................................. 72
D Setting the AGC time constant .................... 72
 ■ IF filter selection .............................................. 73
D IF filter selection .......................................... 73
D Filter passband width setting ...................... 73
D 1st IF filter selection .................................... 74
D IF (DSP) filter shape ...................................74
 ■ Twin PBT operation ......................................... 75
 ■ Noise Blanker .................................................. 76
D NB Set mode ............................................... 76
 ■ Meter peak hold function ................................. 76
 ■ Noise Reduction .............................................. 77
 ■ Dial Lock function ............................................ 77
 ■ Notch function ................................................. 77
6 FUNCTIONS FOR TRANSMIT ..................... 78–84
 ■ VOX function ....................................................78
D Using the VOX function ............................... 78
D Adjusting the VOX function..........................78
 ■ Break-in function ............................................. 79
D Semi Break-in operation ............................. 79
D Full Break-in operation ................................ 79
 ■ Speech compressor ........................................ 80
 ■
Transmit filter width selection ............................80
 ■ ∂TX function ...................................................81
D ∂TX Monitor function .................................. 81
 ■ Monitor function ............................................... 81
 ■ Split frequency operation ................................ 82
 ■ Quick Split function ......................................... 83
D Split frequency offset setting ....................... 83
D Split Lock function ....................................... 83
 ■ Measuring SWR .............................................. 84
D Spot measurement ...................................... 84
D Plot measurement ....................................... 84
7 DV MODE PROGRAMMING ........................ 85–92
 ■ Call sign programming .................................... 85
D “MY”(Yourowncallsign)programming ...... 85
D “UR” (Destination call sign) programming ... 86
D “R1” (Access/Area repeater call sign) and
“R2” (Link/Gateway repeater call sign)
programming ............................................... 87
 ■ Repeater list .................................................... 88
D Repeater list contents ................................. 88
 ■
Repeater list programming ..................................89
 ■ Editing a repeater list ...................................... 91
 ■ Clearing a repeater list ........................................92
8 DV MODE OPERATION ............................. 93–120
 ■ Digital mode operation .................................... 93
 ■ Call sign setting ............................................... 93
 ■ Receiving a D-STAR repeater ......................... 94
 ■ Received call signs.......................................... 95
D Desired call record display .......................... 95
D One-touch reply using the call record ......... 96
 ■ Copying the call sign ....................................... 97
D Copying the call sign memory contents ...... 97
D Copying the call record contents
into call sign memory .................................. 98
 ■ DR (D-STAR Repeater) mode operation .........99
D Communication Form .................................. 99
D Access repeater scan ............................... 100
 ■ Calling CQ ..................................................... 101
D Storing the set data ................................... 102

Icom i9100 Specifications

General

Brand	Icom
Model	i9100
Category	Transceiver
Language	English