Name: IKONIX apt 400XAC Series
Brand: IKONIX
Rating: 4 (1 reviews)

To Next Page

To Previous Page

8. Lock LED: When lit indicates the instrument front panel is locked.

9. Test/Reset Key: Used to turn ON/OFF output voltage, or used to reset

the instrument in the event of a failure condition.

10. Test/Reset LED: When lit indicates output is active, or when blinking

indicates the instrument is in a failure condition.

Table of Contents3
Introduction7
Warranty7
Glossary of Terms8
Safety Symbols10
Safety Precautions10
Service and Maintenance11
Getting Started12
Unpacking and Inspection12
Input/Output Power Considerations12
Instrument Power Switch14
Selecting the Appropriate Wire Gauge14
Power Cable15
Supplied Input Accessories (460XAC)19
Environmental Conditions19
Packaging20
Specifications and Controls21
Specifications21
Measurement Considerations33
Instrument Controls35
Front Panel Controls35
Rear Panel Controls37
Soft Keys38
Programming Instructions40
Powering on the Instrument40
Set Screen Description41
Security42
Lock43
Mem Lock43
System Parameters Description44
Editing System Parameters46
Editing Auto Run Mode47
Editing out Mode48
Editing Single Step (PROGRAM Mode Only)49
Editing Alarm49
Editing Contrast50
Editing Power up50
Editing Loop Cycle (PROGRAM Mode Only)51
Editing V Hi-Lmt & V Lo-Lmt (MANUAL Mode Only)52
Editing F Hi-Lmt & F Lo-Lmt (MANUAL Mode Only)53
Editing Start and End Angle (MANUAL Mode Only)54
Editing Results54
Editing Transient (MANUAL Mode Only)55
Editing OC Fold56
Editing Lock56
Editing Mem Lock57
Editing Volt Sense58
Editing Ext Trig58
Editing Function59
Smartconfig59
Using Memories and Steps (PROGRAM Mode Only)61
Selecting a Memory61
Naming a Memory63
Selecting a Step64
Test Parameters Description64
Editing Test Parameters68
Editing Start and End Angle (PROGRAM Mode Only)70
Editing the Memory Cycle (PROGRAM Mode Only)71
Editing the Memory (PROGRAM Mode Only)72
Editing the Step (PROGRAM Mode Only)72
Editing Voltage73
Editing Frequency74
Editing Transient * (PROGRAM Mode Only)74
Editing Trans-Volt* (PROGRAM Mode Only)75
Editing Trans-Site* (PROGRAM Mode Only)76
Editing Trans-Time* (PROGRAM Mode Only)77
Editing Trans-Cycle* (PROGRAM Mode Only)77
Editing Ramp up (PROGRAM Mode Only)79
Editing Timer Unit (PROGRAM Mode Only)80
Editing Delay (PROGRAM Mode Only)80
Editing Dwell (PROGRAM Mode Only)81
Editing Ramp down (PROGRAM Mode Only)82
Editing Step Cycle (PROGRAM Mode Only)82
Editing a Hi-Lmt & a Lo-Lmt (PROGRAM Mode Only)83
Editing P Hi-Lmt & P Lo-Lmt (PROGRAM Mode Only)84
Editing Ap Hi-Lmt & Ap Lo-Lmt (PROGRAM Mode Only)85
Editing CF Hi-Lmt & CF Lo-Lmt (PROGRAM Mode Only)86
Editing PF Hi-Lmt & PF Lo-Lmt (PROGRAM Mode Only)87
Editing VA Hi-Lmt & VA Lo-Lmt (PROGRAM Mode Only)88
Editing Q Hi-Lmt & Q Lo-Lmt (PROGRAM Mode Only)89
Editing Prompt90
Editing Connect91
Editing Phase Set92
Reviewing Test Results92
Test Modes94
Description of Test Modes94
Initializing a Test in PROGRAM Mode94
AC Output94
DC Output96
Initializing a Test in MANUAL Mode97
AC Output97
DC Output98
Displayed Messages100
OTP - over Temperature Protection100
OCP - over Current Protection100
OPP - over Power Protection100
OVP - Output Voltage Protection101
A-SH - Amplifier Shutdown Protection101
RCP - Reverse Current Protection101
LVP - Low Voltage Protection101
Displayed if the Power Source Detects a Discrepancy between the Output Voltage Setting of 10V or Greater for more than 1 Sec. the LED Indicator the Test/Reset Key will be Blinking101
Remote PLC102
Signal Output102
Signal Input and Remote Interlock102
Bus Remote Interface USB/GPIB/RS-232105
USB/RS-232 Interface105
Connector106
Communication Port Configuration106
Sending and Receiving Commands106
GPIB Interface107
GPIB Connector107
GPIB Address107
Interface Functions107
USB/GPIB/RS-232 Interface Command List108
Basic Commands and Query Commands108
3Φ4W Queries113
1Φ3W Queries115
Program Commands and Companion Queries116
System Commands and Companion Queries119
IEEE 488.2 Common Commands120
Calibration Procedure124
Hardware Verification and Calibration Procedure124
Required Measurement Standard124
Required Measurement Equipment124
Activate Non-Calibration Mode124
Adjust the Power Voltage for Control Circuit124
Adjust the Amplifier Inverter DC Bus Voltage125
Clear the Output High Frequency Ripple and Noise125
Adjust the Output "0" Volts and "110" Volts DC Offset125
Software Calibration Procedure127
Enter Calibration Mode128
Calibration of Voltage 150.0V128
Calibration of Voltage 300.0V129
Calibration of High and Low Current Range130
Calibration of Peak Current131
Options132
Opt. 03 - GPIB Card132
Opt. 06 - Ethernet Card132
Ethernet Card Setup133
Saving New Settings135
Power up135
Ethernet Card Menu137
IP Setup137
IP Address138
Gateway IP138
Subnet Mask138
Device Name139
MAC Address140
Barcode Input140
Autostart142
Ethernet Card Settings Commands and Companion Queries144
Ethernet Card Settings Command Wait Times145
Service and Maintenance146
Replacement Parts List147

Questions and Answers:

Need help?

Do you have a question about the IKONIX apt 400XAC Series and is the answer not in the manual?

IKONIX apt 400XAC Series Specifications

General

Brand	IKONIX
Model	apt 400XAC Series
Category	AC Power Distribution
Language	English

IKONIX apt 400XAC Series User Manual

Table of Contents

Questions and Answers:

IKONIX apt 400XAC Series Specifications