Why is my Janome Sewing Machine needle thread breaking?
The needle thread may be breaking because it is not threaded properly, the tension is too tight, the needle is bent or blunt, the needle is inserted incorrectly, the thread is too heavy for the needle, or the needle thread was not set in the thread holder when embroidery sewing started.
Why is my Janome Skyline S9 noisy?
Your Janome Sewing Machine may be noisy because thread is jammed in the hook area or the feed dog is packed with lint.
What causes skipped stitches on my Janome Skyline S9?
Skipped stitches on your Janome Sewing Machine can occur if the needle is inserted incorrectly, is bent or blunt, or if the needle and/or threads are not suitable for the fabric being sewn. Also, a blue needle may not be used for sewing stretch, very fine or synthetics. Check if the needle thread is not threaded properly, the needle is defective (rusted, burr on needle eye or tip), so change the needle. The embroidery hoop may not be set properly, or the fabric is not stretched tightly enough on the embroidery hoop. Finally, a purple needle may not be used for sewing thick fabrics, denims and across the hem.
Why is my Janome Skyline S9 Sewing Machine bobbin thread breaking?
The bobbin thread on your Janome Sewing Machine may be breaking because it is not threaded properly in the bobbin holder, lint has collected in the bobbin holder, or the bobbin is damaged and does not turn smoothly, so replace the bobbin.
Why is the cloth not feeding smoothly on my Janome Skyline S9 Sewing Machine?
The cloth may not be feeding smoothly on your Janome Sewing Machine because the feed dog is packed with lint, the dual feed foot is not being used for sewing hard to feed material, so use the dual feed foot, the stitches are too fine, so make stitches longer, or the feed dog is lowered.
What to do if my Janome Skyline S9 Sewing Machine is making a crunching sound?
If your Janome Sewing Machine is making a crunching sound, it could be because something is caught between the carriage and the arm, so remove the object, or the carriage is hitting something around the machine.
What to do if my Janome Skyline S9 does not run?
If your Janome Sewing Machine does not run, it could be because the machine is not plugged in, a thread is caught in the hook race, a faulty foot control is plugged in while the machine is turned on, so replace the foot control, or the start/stop button is used for ordinary sewing with the foot control plugged in.
What to do if my Janome Sewing Machine needle breaks?
Your Janome Sewing Machine needle may be breaking due to several reasons: * The needle is inserted incorrectly. * The needle is bent or blunt. * The needle clamp screw is loose. * The needle thread tension is too tight. * The needle is too fine for the fabric being sewn. * An inappropriate presser foot for the selected pattern is being used, so use the correct foot. * The fabric was pulled toward you when sewing free motion quilting with the free motion quilting open-toe foot QO.
What causes seam puckering on my Janome Sewing Machine?
Seam puckering on your Janome Sewing Machine can be caused by the needle tension being too tight, the needle thread or the bobbin thread not being threaded correctly, the needle being too heavy for the fabric being sewn, the stitch length being too long for the fabric, so make stitches shorter, the stitch width being too wide, so reduce the stitch width, or the stabilizer not being used, so use the stabilizer.
What to do if my Janome Skyline S9 Sewing Machine patterns are distorted?
Distorted patterns on your Janome Sewing Machine may be due to the needle thread tension being too loose, the stitch length not being suitable for the fabric being sewn, the feed balancing dial not being properly set, interfacing not being used for sewing stretch and very fine fabrics, so use an interfacing, the embroidery hoop attaching knob being loose, the embroidery hoop hitting something around the machine, the fabric not being stretched tightly enough on the embroidery hoop, the fabric being caught or trapped when sewing embroidery, so stop the machine and free the fabric, the embroidery foot being trapped by a jump thread, so trim the jump thread, or the embroidery foot stumbling on a mound of embroidery threads, so adjust the foot height.
General| Machine Type | Computerized Sewing and Embroidery Machine |
|---|---|
| Built-in Stitches | 300 |
| Embroidery Designs | 250 |
| Maximum Sewing Speed | 1000 stitches per minute |
| USB Ports | Yes |
| Wi-Fi Connectivity | Yes |
| Needle Positions | 91 |
| Stitch Width | 9mm |
| Stitch Length | 5mm |
| Built-in Memory | Yes |
| Screen | LCD Touchscreen |
| Buttonholes | 11 (1-step) |
| Needle Threader | Automatic |
To Next Page