JRC JMA-1030 Series - Rx Port; Tx Port

To Next Page

To Previous Page

Cha

ter 7 INITIAL SETTINGS

7.7.2 RX PORT

Choose the receive port of each signal. It sets to automatic when there is no particular problem.

Auto: Switching automatically between NMEA1, NMEA2, and NMEA3.

7.7.3 TX PORT

Choose the transmit port of each signal.

Main Page

Preface12
Checking the Supplied Items12
Before Operation13
Warning Label Mounting Point19
Equipment Appearance22
- Table of Contents25
Contents26
Glossary31
Chapter 1 INSTALLATION35
- Overview35
- Installation of the Display Unit36
- Installation of the Scanner Unit46
- Connecting the Installation Cable53
  - Nke-1066 Scanner (1.5 Feet)54
  - Nke-2044 Scanner (2 Feet)58
Chapter 2 START the BASIC OPERATION62
- Panel and Screen Display Layout63
- Power On/Off64
- Screen Layout66
- Brief Explanation of Icon's Function74
- Setting the Resident Icons77
Chapter 3 ADJUST the RADAR ECHO78
- Sensitivity Adjustment79
- Sea Clutter Suppression80
- Rain/Snow Clutter Suppression81
- SCREEN BRILLIANCE (Another Operation)82
- Change Range83
Chapter 4 VRM and EBL FUNCTION84
- Operation of Vrm, Ebl84
- Example of Vrm Function84
- Example of Ebl Function85
Chapter 5 VARIOUS FUNCTION ICONS86
- Mob Function (man Overboard)86
- Off-Center Function87
- Cursor Function88
- Guard Zone Function89
- Radar Trails90
  - Setup the Trail Length90
  - SETUP the RADAR TRAILS REF LEVEL, Etc91
- Ais Operations93
- Tt Operations94
- Mode Function96
- Switching Day / Night Mode97
- User Option Key98
- Mark Function99
- Radar Echo103
- Tuning107
- Motion Mode108
- Vector Length109
- Marker109
- Target110
- Nmea Info. Set112
- External Monitor Output113
Chapter 6 OPTION FUNCTIONS114
- Nmea Cable114
- Rectifier Unit114
Chapter 7 INITIAL SETTINGS115
- Language Selection116
- Tuning Adjustment116
- Bearing Adjustment117
- Range Adjustment117
- Antenna Height Set up118
- Noise Level118
- Communication Port Setup119
- I/F Device122
- JRC GPS ( for Future Enhancements)124
Chapter 8 DETAIL PERFORMANCE SETTINGS130
- Sets Radar Echo130
- Tt Function134
- Scanner Function135
- Control138
  - Touch Panel Calibration138
  - Buzzer139
- Maintenance Setting139
- System Setting146
- Display Screen149
- Error Alarm Mask151
- Routine Maintenance153
- Maintenance of each Unit153
Chapter 9 MAINTENANCE and CHECK155
- Performance Check155
- Replacement of Major Parts158
  - Parts Required for Periodic Replacement159
- Fault Finding159
  - Alarms and Other Display Lists159
- Trouble Shooting163
  - Special Parts163
  - Circuit Block to be Repaired163
Chapter 10 AFTER-SALE SERVICE164
- Keeping Period of Maintenance Parts164
- When You Request for Repair164
- Recommended Maintenance164
- Radar Failure Check List165
Chapter 11 DISPOSAL166
- Disposal of the Unit166
- Disposal of Used Magnetron166
- China Rohs166
Chapter 12 SPECIFICATIONS167
- Scanner Dimension168
  - Nke-1066168
  - Nke-2044169
- Display Dimension170
  - Ncd-2256170
- Equipment Outline172
- General Specifications173
- Scanner174
  - Scanner (Nke-1066) Specification174
  - Scanner (Nke-2044) Specification175
- Display176
- Input/ Output Signal178
Appendix180
- Nke-1066 (1.5Ft) Scanner Interconnection Diagram180
- Nke-2044 (2Ft) Scanner Interconnection Diagram181
- Ncd-2256 Display Unit Inter Connection Diagram182
- Jma-1030 Primary Power Supply Diagram183
- Jma-1030 Interconnection Diagram184
- Operation Sheet186
- Menu Function List187
- Declaration of Conformity195

JRC JMA-1030 Series - Rx Port; Tx Port

Table of Contents

Related product manuals