JRC JMA-1030 Series

To Next Page

To Previous Page

Chapter 1 INSTALLATION

 CEILING INSTALLATION

Option: Overhead Mounted Kit

Note: Please slide out, when removing of the front cap.

Front cap

Main Page

Preface12
Checking the Supplied Items12
Before Operation13
Warning Label Mounting Point19
Equipment Appearance22
- Table of Contents25
Contents26
Glossary31
Chapter 1 INSTALLATION35
- Overview35
- Installation of the Display Unit36
- Installation of the Scanner Unit46
- Connecting the Installation Cable53
  - Nke-1066 Scanner (1.5 Feet)54
  - Nke-2044 Scanner (2 Feet)58
Chapter 2 START the BASIC OPERATION62
- Panel and Screen Display Layout63
- Power On/Off64
- Screen Layout66
- Brief Explanation of Icon's Function74
- Setting the Resident Icons77
Chapter 3 ADJUST the RADAR ECHO78
- Sensitivity Adjustment79
- Sea Clutter Suppression80
- Rain/Snow Clutter Suppression81
- SCREEN BRILLIANCE (Another Operation)82
- Change Range83
Chapter 4 VRM and EBL FUNCTION84
- Operation of Vrm, Ebl84
- Example of Vrm Function84
- Example of Ebl Function85
Chapter 5 VARIOUS FUNCTION ICONS86
- Mob Function (man Overboard)86
- Off-Center Function87
- Cursor Function88
- Guard Zone Function89
- Radar Trails90
  - Setup the Trail Length90
  - SETUP the RADAR TRAILS REF LEVEL, Etc91
- Ais Operations93
- Tt Operations94
- Mode Function96
- Switching Day / Night Mode97
- User Option Key98
- Mark Function99
- Radar Echo103
- Tuning107
- Motion Mode108
- Vector Length109
- Marker109
- Target110
- Nmea Info. Set112
- External Monitor Output113
Chapter 6 OPTION FUNCTIONS114
- Nmea Cable114
- Rectifier Unit114
Chapter 7 INITIAL SETTINGS115
- Language Selection116
- Tuning Adjustment116
- Bearing Adjustment117
- Range Adjustment117
- Antenna Height Set up118
- Noise Level118
- Communication Port Setup119
- I/F Device122
- JRC GPS ( for Future Enhancements)124
Chapter 8 DETAIL PERFORMANCE SETTINGS130
- Sets Radar Echo130
- Tt Function134
- Scanner Function135
- Control138
  - Touch Panel Calibration138
  - Buzzer139
- Maintenance Setting139
- System Setting146
- Display Screen149
- Error Alarm Mask151
- Routine Maintenance153
- Maintenance of each Unit153
Chapter 9 MAINTENANCE and CHECK155
- Performance Check155
- Replacement of Major Parts158
  - Parts Required for Periodic Replacement159
- Fault Finding159
  - Alarms and Other Display Lists159
- Trouble Shooting163
  - Special Parts163
  - Circuit Block to be Repaired163
Chapter 10 AFTER-SALE SERVICE164
- Keeping Period of Maintenance Parts164
- When You Request for Repair164
- Recommended Maintenance164
- Radar Failure Check List165
Chapter 11 DISPOSAL166
- Disposal of the Unit166
- Disposal of Used Magnetron166
- China Rohs166
Chapter 12 SPECIFICATIONS167
- Scanner Dimension168
  - Nke-1066168
  - Nke-2044169
- Display Dimension170
  - Ncd-2256170
- Equipment Outline172
- General Specifications173
- Scanner174
  - Scanner (Nke-1066) Specification174
  - Scanner (Nke-2044) Specification175
- Display176
- Input/ Output Signal178
Appendix180
- Nke-1066 (1.5Ft) Scanner Interconnection Diagram180
- Nke-2044 (2Ft) Scanner Interconnection Diagram181
- Ncd-2256 Display Unit Inter Connection Diagram182
- Jma-1030 Primary Power Supply Diagram183
- Jma-1030 Interconnection Diagram184
- Operation Sheet186
- Menu Function List187
- Declaration of Conformity195

JRC JMA-1030 Series - Page 43

Table of Contents

Related product manuals