JUKI SADE - Page 24

To Next Page

To Previous Page

Industrial Sewing Machine SADE

Fig 1. Industrial sewing machine head LU-2810-7 SADE – pictograms placement

Read the instruction

manual.

Signs announcing the need to read

the instructions.

Placed on control box.

Main Page

Table of Contents5
General9
Introduction9
The Machine Identification11
Safety of Use and Warnings11
General Safety Rules11
Safety Rules of the First Assembly13
Safe Working Practices for Connecting to Line Power14
Safe Working Practices During Operation14
Operating Environment17
Items for Which the Power to the Machine Has to be Turned off18
Rules for Safe Cleaning, Maintenance and Repair19
Principles for Safe Handling, Transportation and Unpacking20
Fire Prevention Regulations21
Safety Signs22
Residual Risk Description and Assessment26
Industrial Sewing Machine Lu-2810-7 Sade Description27
Intended Use27
Technical Characteristics28
Construction and Operations30
Optional Equipment40
Preliminary Operations and Putting into Service41
Ordering and Delivery41
Installing the Sewing Machine Components42
Electrical Connections44
Preparation of Industrial Sewing Machine Sade48
Preliminary Operations - General Principles48
First Lubrication49
Attaching the Needle50
Placing Thread Cones51
Attaching and Removing the Bobbin52
Threading the Hook53
Winding a Bobbin54
Threading the Machine Head55
Adjusting the Sewing Machine57
Adjusting the Stitch Length57
Thread Tension58
Thread Take-Up Spring59
Adjusting the Pressure of the Presser Foot60
Needle-To-Hook Relation60
Adjusting the Hook Needle Guard63
Adjusting the Bobbin Case Opening Lever63
Adjusting the Position of Counter Knife, Knife Pressure and Clamp Pressure64
Adjusting the Amount of the Alternating Vertical Movement of the Walking Foot and the Presser Foot66
How to Set the Model of the Machine Head67
Adjusting the Machine Head68
Backstack Setting69
Bobbin Thread Monitor Adjustment69
Operation of Industrial Sewing Machine Sade70
Control Device70
SADE Translation (in Settings)71
Configuration72
Machine Identification (in Settings)73
Needle Change Setting73
Login and Exit Program, Changing User, Manual Operation75
Database Combination Mode75
Peripheral Configuration75
Data Source and Target Configuration76
Product Selection Menu77
Product Options78
Product Definition Options79
Material Definition Options79
Explanation of the Product Profile Parameters82
Thread Tension Settings and Tolerances85
Machine Parameters - Stitch Length Setting86
Label Pre Seam and Machine Stop Point88
Label Post Seam and Setting Stop Point of the Machine89
Message - Post Check90
Label Position End of Automatic Mode90
Tension Monitor91
Product Definition Editor91
Cone Upper Thread92
Cone Bobbin Thread92
Needles92
Sewing Material92
Others93
Needle Wear93
Material Combinations93
Material Editor94
User Management Editor95
Users95
User Identification97
Label Lay-Out Editor97
Search Archive100
Traceability Files101
Database Format101
Log Files101
Free Sew Function102
Exiting the Sade Software102
Translating Sade Modules102
Operating - Initialisation102
Operator Identification103
Sewing Test104
Product Cycle - Operating104
Operator Identification104
Product Selection Screen105
Material Validation by Sade105
Material Identification106
Needle Change106
Sewing107
Controls108
Sewing Speed Table109
Hand Lifter109
Resetting the Safety Clutch109
Adjusting the Automatic Presser Foot Lifter110
Normal-/Reverse-Feed Stitch Needle Entry Points Alignment at the Time of Automatic Reverse Feed Stitching111
Operation Switches113
Machine Protection When Is Not in Use114
Cleaning the Machine During Work115
Maintenance116
Inspections and Maintenance116
Lubrication117
Transport and Handling119
Troubleshooting120
Dismantling and Withdrawal123
Warranty125
Spare Parts Catalogue125

JUKI SADE - Page 24

Table of Contents

Related product manuals