Keysight N9010B - Page 596

596 Keysight N9010B EXA Signal Analyzer Service Guide
Index
see A4BT1 CPU board battery
before troubleshooting, 19
blank display, 59
block diagrams, 356
boot process
problems, 51
boot up process, 47
broadband preamplifiers, 17
C
cables
part numbers, 390
calibration application software, 23
call centers, 39
cautions and warnings, 19
chassis parts
part numbers, 390
checking firmware revision, 46
computer block diagram, 356
connector
see RF input connector
contacting Keysight, 39
corrections menu description, 380
CPU assembly
see A4 CPU assembly
CPU memory card
see A4A1 CPU memory card
D
DANL test, 566
DC probes
use of, 17
diagnostics menus, 369
digital IF
see A3 digital IF assembly
disk drive recovery process, 334
display
see A1A3 LCD
display output, rear panel, 59
displayed average noise level. See
DANL, 566
dress case
see outer case
E
electronic attenuator path, 136, 203
Electronic Attenuator Test (Option
EA3) troubleshooting, 216
electrostatic discharge, 21
entitlement certificate, 14
equipment
adjustments, 26
functional tests, 563
performance verification tests, 26
warm-up time, 562
error messages, 46, 69
ESD Information, 21
ESD safety accessories, 18
external hardware, 403, 404, 405,
406, 409, 410, 411, 412, 413, 414,
416, 417, 419, 421, 423, 424, 433,
434, 435, 436, 498
external VGA monitor, 59
F
fans
see B1, B2 fans
firmware, 46
firmware revision, checking, 46
firmware updating, 592
frequency ranges, 134, 202
frequency readout accuracy test, 569
frequency response
(flatness) test, 579
frequency response (flatness) test
preamp on, 583
front end assembly
see A13 RF front end assembly
front end control board
see A15 front end control assembly
front end troubleshooting kit, 24
front frame
description, 354
part number, 390
removal, 532
front frame parts, 535, 536
front panel interface
see A1A2 front panel interface
board, 390
functional testing
performance verification, 561
functional tests, 46
before performing, 562
equipment list, 563
introduction, 561
vs performance verification
tests, 561
warm-up time, 562
See also individual functional
tests, 561
Functional Tests Guide on
CD-ROM, 16
G
Getting Started Guide on
CD-ROM, 16
green LED, 48
H
handle
see bail handle
hardware
external, 403, 404, 405, 406, 409,
410, 411, 412, 413, 414, 416, 417,
419, 421, 423, 424, 433, 434, 435,
436, 498
high band mixing equations, 229
high band path, 134, 202
High Band Preamp (Option P08, P13,
P26) troubleshooting, 229
high band signal level verification, 67
high band troubleshooting, 169, 173,
218, 223
I
IF Flatness menu description, 380
initialization problem, 60
input attenuators
see A9 and A10 input attenuator
input connector
see RF input connector
instrument
return for service, 43
instrument frequency ranges, 134,
202
instrument messages, 69
Instrument Messages Guide on
CD-ROM, 16
instrument options, 15
instrument packaging, 43
instrument serial number, 42
instrument upgrade, 15
K
keyboard
USB, 25
keypad
part number, 390
Keysight Technologies
contacting, 39
L
LCD
see A1A3 LCD
LED
front panel, 46
green, 48
power on, 53
standby, 51
yellow, 48, 51
license key, 14
licensing software, 593
limiters
RF and transient, 17
LO Band Lock menu description, 383
load, 50 ohm, 17
loading instrument application
software, 333
low band mixing equations, 217
low band path, 134, 202
low band preamplifier path, 136, 203
low band signal level verification, 66
low band switch
see A11 low band switch
low band troubleshooting, 142, 208
M
major assembly locations, 444
manual set, 16