Service ManualService Manual
Operating Lights marLEDOperating Lights marLED
®®
E9 / E9i / E15E9 / E9i / E15
V V 1.0 1.0 33
4.6.14.6.1 CAN CAN Bus Bus and and AddresseAddresses ........................................s ....................................................................................................... 25................. 25
4.6.24.6.2 CAN Bus Terminating Resistor RCAN Bus Terminating Resistor R
AA
.............................................................................................................................. .......... 2525
4.6.34.6.3 RS232 RS232 via via COM COM Interface .................................Interface ..................................................................................................... 27...................... 27
4.6.44.6.4 Pin Pin ConfigurConfiguration ation X2 X2 (CAN, (CAN, RS232) RS232) ............................................................................................................ 28...................... 28
4.74.7 Voltage Measurement using the Service Plug .....................Voltage Measurement using the Service Plug ...................................................... ....... 2929
4.84.8
Wiring Diagram for Operating Foil ........................................................ 30Wiring Diagram for Operating Foil ........................................................ 30
55 Troubleshooting Troubleshooting .............................................................................................................................................................. .... 3131
5.15.1 Error Image with Error Image with Information on Information on possible Causes and possible Causes and Corrective Actions Corrective Actions ... ... 3131
66 Replacement of components Replacement of components .................................................................................................................... 32............ 32
6.16.1 Setup of the Control Electronics with Microfuse ................Setup of the Control Electronics with Microfuse ................................................... ......... 3333
6.26.2 Display of the Display of the operating foil operating foil ................................................................................................................................ .. 3434
6.36.3 Components of the Lamp Body ............................................................ 35Components of the Lamp Body ............................................................ 35
6.46.4 Removing the Light Engine Removing the Light Engine .................................................................................................................................. .. 3636
6.56.5 Inserting the Light Engine Inserting the Light Engine ......................................................................................................................... ............. 3737
6.66.6 Opening the casing ............................................................................ 39Opening the casing ............................................................................ 39
6.76.7 Replacing the Control Electronics ......................................................... 40Replacing the Control Electronics ......................................................... 40
6.86.8 Replacing the operating foil ................................................................. 40Replacing the operating foil ................................................................. 40
6.96.9 System Overview System Overview ........................................................................................................................................................... ... 4242
6.9.16.9.1 Light Light Engine Engine Versions Versions .................................................................................................................................................... 43.................. 43
6.106.10 Light Engine Pin assignment Light Engine Pin assignment ................................................................................................................... ............. 4343
6.116.11 Plug Connections on Plug Connections on Control Electronics and Light Control Electronics and Light Engine Engine ...................................... .......... 4444
6.126.12 Light Engine Locations Light Engine Locations ......................................................................................................................................... ....... 4545
6.136.13 Plug Connections on Plug Connections on the Control the Control Electronics Electronics ................................................................................. ..... 4646
6.13.16.13.1 ConnectioConnections ns for for Supply Supply Voltage Voltage and and Light Light Engines Engines .................................................................... 49...................... 49
6.146.14 Connection for D-Sub Plug .................................................................. 50Connection for D-Sub Plug .................................................................. 50
6.156.15 Installation and Connection of Installation and Connection of the additional Camera the additional Camera Board Board .................................. ........ 5151
6.166.16 Measuring the Input Measuring the Input Voltage on the Voltage on the Control Electronics Control Electronics ......................................... 52............. 52
6.176.17
Configuration of the marLEDConfiguration of the marLED
®®
E via E via DIP Switch DIP Switch ................................................................ ............ 5353
6.186.18 Interface adapter marLEDInterface adapter marLED
®®
EE............................................................... 54............................................................... 54
6.196.19 Software Update ................................................................................ 55Software Update ................................................................................ 55
6.19.16.19.1 Installing the Installing the C2Prog programming software C2Prog programming software on the on the PC PC ............................................................. 55............... 55
6.19.26.19.2 ConnectinConnecting g the the interface interface adapter adapter ...................................................................................................................................... 55.. 55
6.19.36.19.3 ProgrammProgramming ing ......................................................................................................................................................................................... ..... 5656
6.206.20
Replacing the Replacing the Cardan Suspension Cardan Suspension ............................................................................................................ ...... 5959
6.216.21 Closing the casing .............................................................................. 63Closing the casing .............................................................................. 63
77
Change History Change History .............................................................................................................................................................. ...... 6565
7.17.1 Overview of Software Changes ............................................................ 65Overview of Software Changes ............................................................ 65
7.27.2 Overview of Hardware Changes ........................................................... 67Overview of Hardware Changes ........................................................... 67
88 Serial Number Structure ..................................................................... 68Serial Number Structure ..................................................................... 68
To Next Page
Loading...
