KLS Martin marLED E9 - Change History Change History; Overview of Software Changes



Service ManualService Manual
Operating Lights marLEDOperating Lights marLED
®®
E9 / E9i / E15E9 / E9i / E15
V V 1.0 1.0 6565
77

Change HistoryChange History
Hardware / software (HW / SW) statusesHardware / software (HW / SW) statuses
You can learn the HW / SW version of the marLEDYou can learn the HW / SW version of the marLED
®®
E9 / E9i / E15 lamp from the serialE9 / E9i / E15 lamp from the serial
number (see section 8 “Serial Number Structure”, page 68).number (see section 8 “Serial Number Structure”, page 68).
7.17.1 Overview of Software ChangesOverview of Software Changes
LampLamp
typetype
marLEDmarLED
®®
E9 / E9iE9 / E9i
/ E15/ E15
VersionVersion
conc.conc.
Date Date HW HW //
SW-SW-
statusstatus
Description of changeDescription of change
all all all all ==
(Mob.,(Mob.,
Wall,Wall,
Ceiling)Ceiling)

April April 2012 2012 SW SW 0000
Introduction of the new E9, E15 Introduction of the new E9, E15 operating light withoperating light with
firmware on the control electronics version 00-00-32firmware on the control electronics version 00-00-32
all all all all April April 2012 2012 SW SW 0101
Update of the software on the control electronicsUpdate of the software on the control electronics
from 000032 to from 000032 to 00-00-3300-00-33
Reduction of the light intensity in Reduction of the light intensity in Boost Mode. The ratio ofBoost Mode. The ratio of
light distribution between narrow light field and wide light distribution between narrow light field and wide lightlight
field was changed from 1:1 to 4:5.field was changed from 1:1 to 4:5.
Introduction of the marLEDIntroduction of the marLED
®®
RS232 COM interface boardRS232 COM interface board
with software version 0-2-70with software version 0-2-70
all all all all May May 2012 2012 SW SW 0202
Update of the software on the control electronicsUpdate of the software on the control electronics
from 000033 to from 000033 to 00-00-3500-00-35
• • LED LED currents currents can can be be calibrated calibrated to to up up to to 400 400 mAmA
• • Increase Increase of of the the light light intensity intensity in in Boost Boost Mode. Mode. TheThe
ratio of light distribution between narrow light ratio of light distribution between narrow light field andfield and
wide light field was reverted from 4:5 to wide light field was reverted from 4:5 to 1:1.1:1.
all all all all May May 2012 2012 SW SW 0303
Update of the software on the control electronicsUpdate of the software on the control electronics
from 000035 to from 000035 to 00-00-3600-00-36
Via DIP switch 8 on Via DIP switch 8 on the control electronics, it is possible tothe control electronics, it is possible to
choose between the controls for E9 and choose between the controls for E9 and E15. The light fieldE15. The light field
distribution will change accordingly.distribution will change accordingly.
DIP switch 8 = on: Controls are configured for E15.DIP switch 8 = on: Controls are configured for E15.
DIP switch 8 = off: Controls are configured for E9.DIP switch 8 = off: Controls are configured for E9.
all all all all June June 2012 2012 SW SW 0404
Update of the software on the control electronicsUpdate of the software on the control electronics
from 00-00-36 to 00-00-37from 00-00-36 to 00-00-37
The new software prevents unintentional, temporaryThe new software prevents unintentional, temporary
switching off of the lamp when switching off of the lamp when adjustments are madeadjustments are made
using the multipurpose handle (SensoGrip).using the multipurpose handle (SensoGrip).
NOTICENOTICE