Korg C1 - Other Functions; Function Mode; Adjusting Parameter Settings in Function Mode; Functions for Piano Song Mode

12
Other functions
Function Mode
Thepitchaswellastemperamentseingsetc.canbespeci-
edfromtheFunctionMode.Forthefunctionsthatcanbe
set,refertothe“Listoffunctions”below.
 InPartnerMode,noseingsotherthanthevolumebal-
anceforPartnerModecanbespecied.
Adjusting Parameter Settings in the Function Mode
1. Press the FUNCTION buon.
The FUNCTION buon and the PIANO1 buon will
light.
2. Press the appropriate buon shown below to select a
parameter.
Thepressedbuonlightsup,andthecurrentseingap-
pearsinthedisplay.
Save parameter
settings
Auto power off
Octave of
layer mode
Pedal of
layer mode
Delete part of User Song
Pitch
Volume balance
of layer mode
Minimum remaining space for recording
Part volume
Temperament
Stereo sound optimizer
3. Press the + or – buon to select a seing.
Torestorethedefaultseing,simultaneouslypressthe+
and–buons.
Theproceduresforcheckingtheamountofrecord-
ing space remaining, for changing a layer octave
andforsavingparameterseingsdierslightly.
4. To exit Function Mode, press the FUNCTION buon.
TheFUNCTIONbuongoesdark.
Allseingsareappliedtoallsounds.
The seing for the auto power o function is saved
whenitischanged.
Normally,whentheC1/C1Airisturnedo,allparam-
etersreturntotheirfactorydefaultseings.However,
byperformingthe“Saveparameterseings”(seepage
13) operation before the C1/C1 Air is turned o, the
seingsspeciedforthepitchandpartvolumebalance
beforetheC1/C1Airwasturnedocanbesavedasthe
defaultseings.
Functions for Piano Song Mode
InPianoSongMode,theFUNCTIONbuoncanbeusedto
specifythemutinglevelforeachpartofaPianoSong.The
speciedmutinglevelisthesameforbothPart1andPart2.
1. Press the FUNCTION buon; the current muting lev-
el appears in the display.
TheFUNCTIONbuonlightsup.
2. Press the + or – buon to select a seing.
Whenmutedwithaseingof0,therewillbenosound,
andwithaseingof12,thesoundwillbeatfullvol-
ume.
Torestorethedefaultseing(0),simultaneouslypress
the+and–buons.
3. After specifying the desired seing, press the FUNC-
TION buon.
TheFUNCTIONbuongoesdark.
C1AirisinPianoSongMode,SoundDemoSong
ModeorFunctionMode.
2. Press the Play/Pause buon during playback to pause
it.
ThePlay/Pausebuonblinks.
3. To resume playback from the point where it was
paused, press the Play/Pause buon again.
ThePlay/Pausebuonlightsup.
Returning to the Beginning of the Song
1. Press the Stop buon during playback to stop playing
back the performance.
2. Press the Play/Pause buon to start playing back the
song from the beginning.
Skipping to a Specic Measure
1. While the song is playing, stopped or paused, press
the DISPLAY buon; the MEASURE LED in the dis-
play lights up.
Thecurrentmeasureappearsinthedisplay.
2. Press the + or – buon to move to a specic measure.
If playback was stopped, it will be paused (the Play/
Pausebuonblinks)aftermovingtothespecicmea-
sure.PressingthePlay/Pausebuonwillstartplayback
fromthatpoint.
Toquicklyreturntotherstmeasure(001),simultane-
ouslypressthe+and–buons.
Changing the Playback Tempo
Press the DISPLAY buon, and then, after the TEMPO
LED is lit, press the + or – buon to change the tempo.
The seing continues to change while the buonis held
down.
Torestorethetempototheoriginalseing,simultaneously
pressthe+and–buons.
Playing the Right- and Left-hand Parts Separately
AswithPianoSongs,onepartcanbemutedwhiletheother
isplayedback.Referto“Practicingaperformance”onpage
6.
Deleting a Recorded Performance
Eachpartofarecordedperformancecanbedeleted.
1. Press the FUNCTION buon, then the ORGAN2 but-
ton.
2. Press the + or – buon to select the part to be deleted,
and then press the Play/Pause buon to delete the
part.
3. After the part is deleted, press the FUNCTION buon
again.
(Referto“FunctionMode”onpage12“andthe“List
offunctions”onpage13“.)