Korg microSAMPLER User Manual

Effect parameters
55
L DELAY, R DELAY (L, R Delay Time) ...................... [0...1400 ms, 1/64... 1/1]
☞p.53 “L DELAY, C DELAY, R DELAY (L, C, R Delay Time)”
FEEDBACK ....................................................................................[0...127]
☞p.53 “FEEDBACK”
MOD.DEPTH .................................................................................[0...127]
Adjusts the depth of modulation.
LFO FREQ (LFO Frequency) .........................................[0.01...100.00 Hz]
Specifies the LFO frequency. Higher values will make the LFO faster.
LFO SPRD (LFO Spread) ............................................................[–180...180º]
Specifies the LFO phase difference between the left and right channels.
11. TAPE.ECHO
This effect simulates a tape echo. It reproduces the distortion and tonal
change that are characteristic of magnetic tape.
DRY/WET .............................................................. [DRY, 99:1...1:99, WET]
Adjusts the balance between the effect sound and the direct sound.
BPM SYNC (Delay Time Tempo Sync) ........................................... [OFF, ON]
☞p.52 “BPM SYNC (Delay Time Tempo Sync)”
TM RATIO ..................................... [BPM SYNC OFF: 0.5...400.0% (OVER)
/BPM SYNC ON: 12.5...400.0% (OVER)]
☞p.52 “TM RATIO (Time Ratio)”
TAP1 DLY,TAP2 DLY(Tap1,Tap2 Delay Time) .........[0...1400 ms, 1/64...1/1]
Specify the delay times for tap 1 and tap 2. The delay time is determined by
these values in conjunction with the TM RATIO value.
TAP1 LVL,TAP2 LVL (Tap1 Level,Tap2 Level) ............................. [0...127]
Adjust the output levels of tap 1 and tap 2.
FEEDBACK .................................................................................... [0...127]
Adjusts the amount of feedback for tap 1.
HI DAMP ........................................................................................ [0...100%]
Specifies the amount of high-frequency damping.
LO DAMP ....................................................................................... [0...100%]
Specifies the amount of low-frequency damping.
TRIM .................................................................................................. [0...127]
Adjusts the input level to the effect.
SATURATN (Tape Saturation) ..................................................... [0...127]
Adjusts the amount of distortion in the effect sound.
WOW FREQ (WOW Flutter Frequency) ............................[0.01...100.00 Hz]
Adjusts the speed of pitch change in units of Hz.
WOW.DEPTH (WOW Flutter Depth) ................................................ [0...127]
Adjusts the depth of pitch change.
PRE TONE .......................................................................................... [0...127]
Adjusts the tone of the input sound.
SPREAD ............................................................................................. [0...127]
☞p.53 “SPREAD”
Wow Flutter
Tap2 Level
Tape
Saturation
Dry / Wet
Trim
Tap1 Level
Dry / Wet
Feedback
High / Low Damp
Pre Tone
Delay
Spread
Left
Right
Wet: Mono In - Stereo Out
Effect parameters

Korg microSAMPLER Specifications

General

Sampling Frequency	48 kHz
A/D Conversion	24-bit
D/A Conversion	24-bit
Type	Sampler Keyboard
Keyboard	37 keys (velocity sensitive)
Number of Samples	36 per bank
Sequencer	16, 000 notes
Display	16 character x 2 line LCD
Outputs	L/Mono, R (1/4" Phone), Headphones (1/4" Stereo Phone)
USB	USB MIDI
Power Supply	AC adapter (included)
Inputs	Audio Input (1/4" Phone), Mic Input (1/8" Phone)