KUHN Venta 3030

To Next Page

To Previous Page

Venta 3030-3530-4030

6. - Machine delivery

RN034AGB D

Seed Drill

Never lift the seed drill and power harrow

together.

2052421

Main Page

Dear Owner3
Table of Contents4
Contents4
Identification of the Machine9
Rear View9
Model Identification Plate10
Optional Equipment12
Safety13
Description of Symbols Used in this Document13
Safety Instructions14
Introduction14
Read and Follow the Safety Instructions14
Precautions to be Taken before Carrying out any Operations on the Machine15
Precautions to Take before Using the Machine15
Precautions When Driving16
Precautions When Driving on Public Roads17
Maximum Speed21
Precautions When Coupling22
Hydraulic Circuit23
Precautions During Manoeuvres24
Remote Controlled Components24
Safety Decals24
Waste Disposal24
Precautions for Maintenance and Repair Work25
Projection of Stones and Foreign Objects25
Precautions for Machine Use26
Precautions to Take before Using the Parking Stands26
Location and Description of Safety Decals on the Machine27
Location of Safety Decals27
Description of Safety Decals29
Road Safety Equipment and Recommendations32
Likely Critical Failures34
Incorrect Use of the Machine by the User34
Limit State Criteria34
Machine Specifications35
Description and Glossary35
Technical Specifications37
Required Equipment38
Seedflex Seeding Units38
Control Terminal38
Top Link39
Hydraulic Blower Drive40
Sound Levels41
Machine Delivery42
Machine Parking42
Unloading with an Overhead Crane43
Unloading with a Forklift43
Putting into Service45
Description of Control Elements45
Control Box Description47
Preparing the Tractor48
Coupling the Machine50
Lift Sensor Adjusment54
Description of Coupling Elements55
Blower Unit Drive55
Adjusting the Machine61
Covering Harrow Adjustment61
Adjusting the Tramlining Rhythm62
Adjustment of the Fill Level Sensor63
Instructions for Transport65
Putting the Machine into Transport Position65
Steps65
Pre-Emergence Markers (Optional Equipment)66
Radar Arm (Optional Equipment)66
Metering Unit66
Parallelogram Linkage66
Covering Harrow67
Conformity with the Road Regulations68
Machine Transport Using Transport Means68
Instructions for Work69
Items to Check before Starting Work69
The Application Rate69
The Tramlining70
Putting the Machine into Work Position70
Lower the Harrow71
Lower the Radar Arm (Optional Equipment)71
Lower the Pre-Emergence Marker (Optional Equipment)72
Adjustments in Working Position73
Coulter Bar Adjustment75
Ground Pressure Adjustment76
Covering Harrow Adjustment76
Filling the Hopper78
Adjusting the Metering Unit80
Blower80
Agitator82
Adjusting the Metering Unit Opening for Large Seeds (Large Grooves)83
Adjusting the Metering Unit Opening for Small Seeds (Small Grooves)84
Stationary Calibration Test86
Machine Use89
Emptying the Hopper90
Partial Emptying (A)90
Cleaning the Metering Unit (B)91
Uncoupling the Machine92
Parking Without Soil Preparation Tool92
Parking the Combination95
Optional Equipment96
Tramline Shut-Off Valves96
Removal of the Mechanical Valve96
Fitting of the Tramlining Valve97
Half-Width Shut-Off98
Lighting99
Lighting/Signalling for Seed Drill Without Covering Harrow99
Side Reflective Panels100
Pre-Emergence Markers100
Adjusting the Position of the Disk101
Angle Adjustment101
Length Adjustment101
Transport Position102
Wheel Scraper102
Seeding Disk Cleaners103
Radar103
Working Light104
Sealing Lip for Fava Beans104
Fertilizer Dispenser105
Volume Reducer105
Free Return106
Balance KERN106
Distribution Head with VISTAFLOW Valves107
Maintenance and Storage108
Frequency Chart108
Cleaning the Machine109
Lubrication110
Maintenance112
Checking that the Cover Is Locked112
Check Metering Unit Seal Lips113
Checking the Blower Hydraulic Drive114
Checking the Covering Harrow Tines114
Control of the Seedflex Seeding Units114
Checking the Seed Transfer Tubes115
Checking the Lighting Equipment115
Oil Change116
Check the Functioning of the Tramlining Valves119
Storage and Pre/Post Season Checks120
At the End of each Season120
At the Start of each Season121
Storage121
Dismantling and Scrapping of the Machine122
Troubleshooting Guide123
Calculating the Load on an Axle125
Limited Warranty133

KUHN Venta 3030 - Page 44

Table of Contents

Related product manuals