LeCroy WaveRunner 6Zi

To Next Page

To Previous Page

WaveRunner 6 Zi Oscilloscopes

WR6Zi-GSM-E

Note: If the processing time is greater than the acquire time, the data

in memory gets overwritten. In this case, the instrument issues a

Channel data is not continuous in ROLL mode!!! warning and rolling

starts over again.

Main Page

Default Chapter1
- Getting Started1
- Table of Contents4
Welcome12
- Waverunner 6 Zi Features12
- Core Oscilloscope Functions12
- Compatible Options and Accessories12
- Reference12
- Support12
- Thank You13
- Safety Requirements13
- Safety Symbols13
- Operating Environment15
- Safety Certification16
- Cooling17
- AC Power Source17
- Power Consumption18
- Power and Ground Connections18
- Calibration21
- Cleaning21
- Abnormal Conditions22
Hardware23
- Front Panel23
- Rotating and Tilting the Display24
- I/O Panel27
- Back Panel28
Basic Controls29
- Hardware and Software Controls29
- Front Panel Controls29
- Front Panel Groupings30
- Trigger Front Panel Controls31
- Horizontal Front Panel Controls33
- Vertical Front Panel Controls33
- Math, Zoom, and Memory Indicators and Controls34
- The Wavepilot Control Area and the Superknob35
Probe and Signal Connection Interfaces42
- Probe and Signal Connection Interfaces Overview42
- Probe Interfaces43
- Probe Interfaces Overview43
- Probus Probe and Cable Connecting Interface45
- Probes46
- Passive Probe Compensation47
Display Dashboard48
- Display Dashboard Overview48
- Screen Layout, Groupings, and Controls48
- Menu Bar49
- The Quick Access Toolbar49
- The Signal Display Grid50
- Signal Display Grid Pop-Up Menu52
- Trace Descriptor Labels52
- Actions for Trace Buttons54
- Annotating Traces54
- Dialog Area56
- Touch Screen Controls56
- Actions for Trace Buttons61
- Message Bar62
- Turning on Channels and Traces62
Turning on Channels and Traces64
- Timebase64
- Timebase Overview64
- Timebase Setup and Control64
Timebase64
Sampling Modes65
- Sampling Modes Overview65
- Selecting a Sampling Mode65
- Single-Shot Sampling Mode65
- Basic Capture Technique65
- Sequence Display Modes68
- Sequence Mode Setup69
- Zooming Segments in Sequence Mode71
- Displaying an Individual Segment72
- Viewing Time Stamps73
- RIS Sampling Mode - for Higher Sampling Rates73
- Roll Mode74
Vertical76
- Adjusting Sensitivity and Position76
- Adjusting Sensitivity76
- Adjusting the Waveform's Position76
- Coupling77
- Overload Protection77
- Setting Coupling77
- Probe Attenuation77
- Setting up Probe Attenuation77
- Bandwidth Limits78
- Setting Bandwidth Limits78
- Linear and (Sinx)/X Interpolation79
- Interpolation Setup79
- Inverting Waveforms79
- Finding Scale79
- Using Find Scale79
- Variable Gain79
- Enabling Variable Gain80
- Channel Deskew80
- Channel Deskew Setup80
Trigger81
- Trigger Overview81
- Trigger Types81
- Edge82
- Width82
- Pattern (Logic)82
- Smart82
- Measurement84
- Mulitstage85
- Serial Trigger86
- Trigger Settings86
- Trigger Setup87
- Optimize for HF91
- Width Condition Is92
- Holdoff by Time or Events92
- Auxiliary Input Trigger94
- Triggerscan95
- Training Triggerscan96
- Starting Triggerscan97
Viewing Waveforms98
- Saving Triggerscan Setups98
- Display98
- Display Overview98
- Display Setup99
- Moving Traces from Grid to Grid102
- Displays Containing Masks102
- Dual Display Grid Selection103
- Persistence104
- Persistence Overview104
- Persistence Setup104
- Wavestream Display Mode106
- Adjusting Trace Intensity106
Zooming Waveforms107
- Zooming Waveforms Overview107
- Previewing Zoomed Waveforms108
- Zooming a Single Channel108
- Touch-And-Drag Zooming110
- Turning off Zoom111
Measuring with Cursors112
- Measuring with Cursors Overview112
- Cursor Measurement Icons112
- Cursors Setup113
- Quick Display113
- Absolute Cursors Setup113
- Setting up Relative Cursors114
- Cursors on Math Functions114
Measurement Parameters115
- Measurement Parameters Overview115
- Turning on Parameters115
- Quick Access to Parameter Setup Dialogs115
- Parameter Setup116
- Measure Modes118
- Standard Vertical Parameters118
- Standard Horizontal Parameters118
- Selecting Measure Modes118
- Help Markers118
- Help Markers Setup120
Measurement Parameter Analysis121
- Measurement Parameter Analysis Overview121
- Creating and Viewing a Histogram123
- Single Parameter Histogram Setup124
- Viewing Thumbnail Histograms (Histicons)128
- Persistence Histogram129
- Persistence Trace Range130
- Persistence Sigma130
- Creating and Viewing a Trend130
- Creating a Track View131
- Pass-Fail Parameter Testing132
- Pass/Fail Parameter Testing Overview132
- Testing and Enabling Pass/Fail Conditions133
- Pass/Fail Setup on Qx Dialogs134
- The Actions Dialog138
Math141
- Math Traces and Functions Overview141
- Math Setup142
Mask Testing144
- Creating a Mask144
- Quick Access to Pass/Fail Setup Dialogs146
- Removing a Mask from the Display146
- Right-Hand Dialogs147
- Wavescan Overview149
- Signal Views150
- Search Modes150
- Parameter Measurements151
- Sampling Mode151
Customization Overview152
Documenting Your Work Using Labnotebook154
- Labnotebook Overivew154
- Labnotebook155
Save/Recall159
- Save/Recall Overview159
- Saving and Recalling Setups160
- Saving Oscilloscope Setup(S)160
- Recalling Oscilloscope Setup(S)160
- Recalling Default Settings161
- Saving and Recalling Waveforms162
- Saving Waveforms162
- Recalling Waveforms165
Utilities167
- Utilities Setup167
- Utilities Overview167
- Status169
- Remote Communication169
- Printing and Hardcopy Functions171
- Aux Output179
- Date and Time181
- Options182
- Disk Utilities182
- Preferences184
- Preference Setup Overview184
- Acquisition185
- E-Mail187
- Color189
- Miscellaneous190
System Recovery Tool190
- Restoring Software Using the Acronis Application190
- Restarting the Application194
- Restarting the Operating System194
Reference195
- Waverunner 6 Zi Specifications195
- Certifications195
- CE Declaration of Conformity195
- EMC Directive195
- Low-Voltage Directive196
- UL and Cul197
- Contact Lecroy for Support198
- Windows License Agreement212
Index213

LeCroy WaveRunner 6Zi - Page 75

Table of Contents

Related product manuals