Logosol PH260 - User Manual

Questions and Answers

L
lauren64Aug 23, 2025
Why does the motor get overheated on my Logosol PH260 Saw?
- H
  Heather Tyler DVMAug 23, 2025
  If the motor of your Logosol Saw is overheating, consider the following: * Check for wood debris accumulated in the machine's chassis or around the motor's cooling fans, and clear any obstructions. * Dull knives can cause overheating. Grind or replace them. * Ensure the power supply provides the correct voltage on all phases. * Inspect the power supply connection to the machine for looseness or poor connections. * If the upper cutter is removing too much wood, especially with wide, hard, or oversized workpieces, plane the material to size beforehand. * Reduce the feeding speed.
R
Richard BatesSep 7, 2025
Why are the planing knives cutting away the highest points of the moulding pattern on my Logosol PH260 Saw?
- K
  Kristen BrownSep 8, 2025
  If the planing knives are cutting away the highest points of the moulding pattern on your Logosol Saw, it may be due to: * The planing knives removing too much wood. Set the takeoff of the planing knives to 1 mm (or slightly less) using Logosol’s setting block (ref. no. 7500-000-1020) or a magnetic adjuster for the upper cutter (ref. no. 7500-001-0050). * The moulding knives being ground incorrectly. Use adjustable short knife clamping gibs (ref. no. 7000-000-9506) to adjust the moulding knives correctly.
O
oliviabrewerSep 6, 2025
Why are the edges of the molding knives visible in the machined moulding profile of my Logosol PH260?
- C
  Charles HopkinsSep 6, 2025
  If the edges of the molding knives are visible in the machined moulding profile when using your Logosol Saw, it could be because: * The planing knives do not cut away enough wood. Set the takeoff of the planing knives to 1 mm (or slightly more) using Logosol’s setting block (ref. no. 7500-000-1020) or a magnetic adjuster for the upper cutter (ref. no. 7500-001-0050). * The moulding knives are ground incorrectly. Regrind the moulding knives so their edges do not protrude over the level of the planing knives.
K
karen60Sep 4, 2025
Why is there vibration or rumble in the side cutter of my Logosol PH260 Saw?
- M
  Michael EvansSep 4, 2025
  If you're experiencing vibration or rumble in the side cutter of your Logosol Saw, check these potential causes: * Incorrectly mounted moulding knives. Demount the cutter head, and clean and correctly mount the knives and chip breakers. * Incorrectly ground moulding knives. Grind the knives in pairs so that they are identical on opposite sides of the cutter. * Defective bearing. Replace the bearing. * Bent spindle shaft due to overloading. Replace the spindle shaft. * Defective belt transmission. Clean the belt pulleys and replace the Poly V belt.
R
Randy BrownSep 3, 2025
Why is there rumbling or vibration in the upper or the lower cutter of my Logosol PH260 Saw?
- C
  collinssusanSep 3, 2025
  If you're experiencing rumbling or vibration in the upper or lower cutter of your Logosol Saw, consider these possibilities: * The moulding knives may be incorrectly mounted. Clean the cutter and mount the knives and chip breakers correctly. * The moulding knives or planing knives might be incorrectly ground. Grind the knives in pairs to ensure they are identical on opposite sides of the cutter. * The bearing could be defective. Clean the bearing housing and replace the ball bearing. * The belt transmission may be defective. Clean the belt pulleys and replace the Poly V belt.
M
Michael MyersSep 1, 2025
What to do if the thickness of the board does not correspond to the setting of the scale on Logosol Saw?
- A
  Ashley JohnsonSep 1, 2025
  If the board thickness doesn't match the scale setting on your Logosol Saw, it could be due to: * Incorrect takeoff setting of the knives in the upper cutter. Set the takeoff to 1 mm using Logosol’s setting block (ref. no. 7500-000-1020) or a magnetic adjuster for the upper cutter (ref. no. 7500-001-0050). * Incorrectly set pointer of the height scale. Machine a test board, measure it, and then set the pointer to that measurement.
E
Eric ThompsonAug 31, 2025
Why is the surface of the workpiece’s right side below par with Logosol Saw?
- G
  gonzalezronaldAug 31, 2025
  If the surface quality of the right side of the workpiece is poor when using your Logosol Saw, it may be because: * The locking handle of the movable side cutter has not been tightened. Ensure you pull the handle tight before planing or moulding.
H
hancockgaryAug 29, 2025
Why is the workpiece fed jerkily through the Logosol PH260 Saw?
- D
  Dr. Cathy Gonzalez MDAug 29, 2025
  If the workpiece is being fed jerkily through your Logosol Saw, there are a couple of potential reasons: * The machine table may be covered with resin or rust. Clean it with Logosol’s Machine Cleaner (ref. no. 7500-001-5000) and lubricate it with Logosol’s Low Friction Agent (ref. no. 7500-001-5050). * One of the feed rollers may have been bent. Replace the bent feed roller.
C
Connie LewisAug 27, 2025
How to fix in- and out-feed marks on Logosol PH260 Saw?
- A
  Amanda MarshallAug 27, 2025
  If you notice in- and out-feed marks when using your Logosol Saw, check the following: * The in- and out-feed tables may be incorrectly adjusted. Ensure they are at the same height as the machine table and aligned, or slightly higher at the outer ends. * The workpieces may not be butted together when fed into the machine. Butt the workpieces end to end. * The feeding pressure of the feed rollers may be incorrectly adjusted. Make sure the feeding pressure is sufficient and the rollers are balanced horizontally over the workpiece. * The workpiece may be bent or warped. Slightly lift the back end when feeding it in. * There might be play in the suspension of the machine table. Check if the table wobbles and read Levelling the machine table.