What does the 'Flooded?' message mean on Magnetrol eclipse Enhanced Model 705 Transmitter?
The 'Flooded?' message indicates a loss of level signal, possibly due to flooding (twin rod probes only). Decrease the level in the vessel and set the transmitter to a lower dielectric range.
How to fix inaccurate LEVEL, % OUTPUT, and LOOP values on Magnetrol eclipse Enhanced Model 705?
If the LEVEL, % OUTPUT, and LOOP values are all inaccurate, the basic configuration data might be questionable. Try reconfiguring the Probe Model, Probe Mount, Probe Length, or Level Offset. Also, ensure the Level is accurate and verify the 4 mA and 20 mA Loop values.
Why is LEVEL reading high when it should be zero on Magnetrol eclipse Enhanced Model 705?
If the LEVEL value is reading high when it should be zero, the transmitter might be loose or disconnected from the probe. Ensure the transmitter is securely connected.
How to resolve WeakSgnl error on Magnetrol Transmitter?
If you are getting a WeakSgnl error, the signal amplitude is lower than desired. Set the transmitter to a lower dielectric range and increase the sensitivity.
What does it mean when EOP is less than probe length on Magnetrol eclipse Enhanced Model 705?
If the EOP (End of Probe) is less than the Probe Length, the End of Probe signal from a dry probe is out of range. Ensure the probe length is entered correctly. Also, set the transmitter to a lower dielectric range and ensure proper blocking distance.
What to do if LEVEL reading is correct but LOOP is stuck at 4 mA on Magnetrol eclipse Enhanced Model 705 Transmitter?
If the LEVEL reading on the Display is correct, but the LOOP is stuck on 4 mA, the basic configuration data might be questionable. Set the POLL ADR to 0 if you are not using HART multi-drop.
How to fix LEVEL, % OUTPUT, and LOOP values at maximum on Magnetrol eclipse Enhanced Model 705?
If the LEVEL, % OUTPUT, and LOOP values are all at the maximum level, there might be a configuration issue with the single rod probe. Increase the Blocking Distance and increase the Dielectric Range.
Why are LEVEL, % OUTPUT, and LOOP values reading low on Magnetrol eclipse Enhanced Model 705 Transmitter?
If the LEVEL, % OUTPUT, and LOOP values are all reading low compared to the actual level, it could be due to a lower dielectric material over a higher dielectric material, such as foam over water. Try adjusting the Threshold settings.
What causes high LEVEL, % OUTPUT, and LOOP readings on Magnetrol eclipse Enhanced Model 705 Transmitter?
If the LEVEL, % OUTPUT, and LOOP values are all reading high compared to the actual level, there might be an obstruction in the tank affecting the single rod probe. Adjust the sensitivity until the obstruction is ignored, or relocate the probe away from the obstruction.
How to correct consistently high or low LEVEL readings on Magnetrol eclipse Enhanced Model 705 Transmitter?
If LEVEL readings are repeatable but consistently high or low from the actual level by a fixed amount, the configuration data might not accurately match the probe length or tank height. Ensure the proper Probe Model and probe length are set. You can also adjust the trim level value by the amount of noted inaccuracy.
General| Type | Guided Wave Radar Level Transmitter |
|---|---|
| Application | Level Measurement |
| Measurement Range | Up to 30 m |
| Accuracy | ± 3 mm (0.12 inch) |
| Output Signal | 4-20 mA HART |
| Power Supply | 12 to 42 VDC |
| Process Temperature | -196 to 400°C (-320 to 752°F) |
| Process Pressure | Up to 40 bar (580 psi) |
| Approvals | ATEX, IECEx, FM, CSA |
| Communication Protocol | HART |
| Enclosure Rating | IP66/67, NEMA 4X |
| Material | 316L Stainless Steel, Hastelloy C-276 |
| Communication | HART |
| Process Connection | Threaded, flanged |
To Next Page