MAN B&W 19.06
Page 1 of 1
MAN Diesel
MAN B&W S42MC, S40MCC, S/L35MC, 35MC-C,
S26MC
198 79 12-7.0
List of Spare Parts, Unrestricted Service
Fig. 19.06.01: List of spare parts, unrestricted service: 4 87 601
Cylinder cover, plate 901 and others
1 Cylinder cover with fuel, exhaust and starting
valves, indicator valve and sealing rings (disas-
sembled).
½ set Studs for 1 cylinder cover
Piston, plate 902
1 Piston complete (with cooling pipe), piston rod,
piston rings and stuffing box, studs and nuts
1 set Piston rings for 1 cylinder
Cylinder liner, plate 903
1 Cylinder liner inclusive of sealing rings and
gaskets.
Cylinder lubricator, plate 903
1
)
Standard Spare parts
1 set Spares for MAN B&W Alpha lubricator for 1 cyl.
1 Lubricator
2 Feed back sensor, complete
1 Suction filter element for pump station
1 Pressure filter element for pump station
1 Complete sets of O-rings for lubricator (de-
pending on No. of lubricating per. cylinder)
6 3A, 3 pcs. 12A ceramic or sand filled fuses 6.3
x 32 mm, for MCU, BCU & SBU
2 LED’s for visual feed back indication
or
1 set LED’s for visual feed back indication
Connecting rod, and crosshead bearing, plate 904
1 Telescopic pipe with bushing for 1 cylinder
1 Crankpin bearing shells in 2/2 with studs and
nuts
1 Crosshead bearing shell lower part with studs
and nuts
2 Thrust piece
Main bearing and thrust block, plate 905
1 set Thrust pads for one face of each size, if differ-
ent for ‘ahead’ and ‘astern’
Chain drive, plate 906
1
)
1 Of each type of bearings for camshaft at chain
drive and chain tightener
6 Camshaft chain links. Only for ABS, LR and NK
1 Mechanically driven cylinder lubricator drive:
chain links or gear wheels
1 Guide ring 2/2 for camshaft bearing
Starting valve, plate 907
1 Starting valve, complete
Exhaust valve, plate 908
2 Exhaust valves complete. 1 only for GL)
1 Pressure pipe for exhaust valve pipe
Fuel pump, plate 909
1 Fuel pump barrel, complete with plunger
1 High-pressure pipe, each type
1 Suction and puncture valve, complete
Fuel valve, plate 909
2 Fuel valves per cylinder for all cylinders on one
engine, and a sufficient number of valve parts,
excluding the body, to form with those fitted on
each cylinder for a complete engine set for BV,
CCS, GL, KR, LR, NK, RINA, RS and IACS
2 Fuel valves per cylinder for half the number of
cylinders on one engine, and a sufficient num-
ber of valve parts, excluding the body, to form
with those fitted on each cylinder for a com-
plete engine set for ABS
1 set Fuel valves for all cylinders on one engine for
DNV
Turbocharger, plate 910
1 Set of maker’s standard spare parts
1 a) Spare rotor for one turbocharger, including:
compressor wheel, rotor shaft with turbine
blades and partition wall, if any
Scavenge air blower, plate 910
1 set
a)
Rotor, rotor shaft, gear wheel or equivalent
working parts
1 set Bearings for electric motor
1 set Bearings for blower wheel
1 Belt, if applied
1 set Packing for blower wheel
Bedplate, plate 912
1 Main bearing shell in 2/2 of each size
1 set Studs and nuts for 1 main bearing
1
) MD required spare parts.
a) Only required for RS. To be ordered separately as
option: 4 87 660 for other classification societies.
Please note: Plate number refers to Instruction Book,
Vol. III containing plates with spare parts.
Spare parts are requested by the following Classes
only: GL, KR, NK and RS, while just recommended by:
ABS, DNV and LR, but neither requested nor recom-
mended by: BV, CCS and RINA.
To Next Page
Loading...
