MIMAKI TS34-1800A - Page 3

© 2011 MIMAKI ENGINEERING CO.,LTD.
Maintenance Manual Contents R.1.0 P.1
MAINTENANCE MANUAL > Maintenance Manual Contents
Model JV34-1800A Issued 2011.10.17 Revised F/W ver. 1.20 Remark
Maintenance Manual Contents
1.0
Rev.
1 Operating Principle
1.1 Basic Operation
1.1.1 Main Switch Power ON
1.1.2 Sub Switch Power ON
1.1.3 Initial Machine Operation
1.1.4 Detection of a Media Width
1.1.5 Power OFF
1.2
Maintenance Function
1.2.1 CARRIAGE OUT
1.2.2 WIPER REPLACE
1.2.3 NOZZLE WASH
1.2.4 CR.MAINTENANCE
1.2.5 FILL UP INK
1.2.6 DISCHARGE&WASH
1.2.7 Waste Ink Tank Warning
1.3
Ink System
1.3.1 Configuration
1.3.2 Ink System Error Monitoring
1.3.3 Supply Cartridge Control and
Selection
1.3.4 Cartridge LED Control
1.3.5 Supply Valve Control
1.3.6 Monitoring of the Amount of
Remaining Ink
1.3.7 Use-up Cleaning
1.3.8 Ink Suction and Discharge Control
1.3.9 Initial Filling
2 Electrical Parts
2.1
Block Diagram
2.1.1 Connection Diagram Inside the Main
Body
2.1.2 Connection Diagram Outside the Main
Body
2.2
Operation Explanation
2.2.1 Operation Explanation
2.3
Circuit Board Specifications
2.3.1 Power Supply PCB Assy
2.3.2 Main PCB Assy
2.3.3 PRAM PCB Assy
2.3.4 Regenerative Resistivity PCB Assy
2.3.5 Station PCB Assy
2.3.6 X-axis Motor Relay PCB Assy
2.3.7 HDC PCB Assy
2.3.8 Slider PCB Assy
2.3.9 Head Memory PCB Assy
2.3.10 LED PCB Assy
2.3.11 Keyboard PCB Assy
2.3.12 Take-up PCB Assy
2.3.13 Encoder PCB Assy
3 Workflow
3.1 Ink Related Parts
3.1.1 Replacement of the Head Unit
3.1.2 Replacement of the Cartridge Assy
3.1.3 Replacement of the Wiper Unit
3.1.4 Replacement of the Cutter Assy
3.2 Driving Parts
3.2.1 Replacement of the X-axis Motor
3.2.2 Replacement of the Y-axis Motor
3.2.3 Replacement of the Y Drive Belt
3.2.4 Replacement of the Linear Encoder
Scale
3.3 Electrical Parts
3.3.1 Replacement of the Main PCB Assy
4 Adjustment Items
4.1 Operation Matrix
4.1.1 Matrix of Operations and Adjustments
4.2 Adjustment Function
4.2.1 [HEAD ADJUST] SLANT ADJUST
4.2.2 [HEAD ADJUST] STAGGER ADJUST
4.2.3 [HEAD ADJUST] AVERAGING
ADJUST
4.2.4 [HEAD ADJUST] DROP.POS
4.2.5 [HEAD ADJUST] LevelSurfaceCHK
4.2.6 EDGE ADJUST
4.2.7 MEDIA COMP.2
4.2.8 POINTER OFFSET
4.2.9 CAPPING
4.2.10 HEAD ID
4.2.11 HEAD WASH
4.2.12 MANUALhead WASH
4.2.13 MOTOR CURRENT
4.2.14 SERIAL No.
4.2.15 DEALER No.
4.2.16 DEFAULT SET
4.2.17 REPLACE PARTS
4.3 Mechanical Adjustment
4.3.1 Adjustment of the Mounting Location
for the Cutter
4.3.2 Adjustment of the Station Height
4.3.3 Adjustment of the Wiper Height
4.3.4 Positioning of the Encoder Sensor
4.3.5 Centering of the Roll Holder
4.3.6 Positioning of the Wiper Drive Link