APPX
Appendix 4 List of Special Relay Areas
821
A
SM1213 Data logging setting No.1
Data logging end
Off: Not completed
On: Completed
This relay switches to on when the data
logging is completed. For continuous
logging, the corresponding bit switches to
on when writing reaches the maximum
number of storage files and data logging is
completed (with "Stop" set for the operation
at the time when the number of save files
exceeds the limit). For trigger logging, the
corresponding bit switches to on when data
collection for the specified number of
records has been completed followed by
writing into the SD memory card after the
trigger condition was satisfied. The bit also
switches to on when an error is generated
(except for data logging error caused by
online program change) during the data
logging execution.
S (Status change) Rn
*1
RnP
RnSF
SM1214 Data logging setting No.1
Data logging trigger
OffOn:Triggered The system switches this relay to on when
the specified trigger condition is satisfied.
S (Status change) Rn
*1
RnP
RnSF
SM1215 Data logging setting No.1
After data logging trigger
Off: Not post triggering
On: Post triggering
• This relay switches to on once data
logging triggering occurs. The ON state is
maintained even when the data logging is
completed. However, this relay is off when
the data logging is in suspend/waiting for
start without collection/stop mode
• This relay also switches to off when the
CPU module is moved from RUN to
STOP mode and therefore the data
collection is halted.
S (Status change) Rn
*1
RnP
RnSF
SM1216 Data logging setting No.1
Data logging error
Off: No error
On: Error
• This relay switches to on when a data
logging function error is generated.
• This relay switches to off when the setting
is registered or by the stop command
from CPU Module Logging Configuration
Tool .
S (Status change) Rn
*1
RnP
RnSF
SM1217 Data logging setting No.1
Data logging data saving in
progress
Off: Not in progress
On: In progress
This relay turns on when data in the internal
buffer is being saved in the SD memory card
or function memory with the data logging.
S (Status change) Rn
*1
RnP
RnSF
SM1218 Data logging setting No.1
Logging data storage file
switching in progress
Off: Not in progress
On: In progress
This relay switches to on when storage file
switching is in progress.
S (Status change) Rn
*1
RnP
RnSF
SM1219 Data logging setting No.1
Data logging file transfer
execution status flag
Off: Not executed
On: Being executed
• This relay turns on at the start of the data
logging file transfer function or
transferring of data logging files to the
data memory.
• This relay turns off at the completion of
the data logging file transfer function or
transferring of data logging transfer files
to the data memory.
S (Status change) Rn
*1
SM1220
to
SM1229
Data logging setting No.2 Same configuration as the
setting No.1
Data configuration is the same as the
setting No.1 (SM1210 to SM1219).
Same configuration as the
setting No.1
Rn
*1
RnP
*2
RnSF
*2
SM1230
to
SM1239
Data logging setting No.3 Same configuration as the
setting No.1
Data configuration is the same as the
setting No.1 (SM1210 to SM1219).
Same configuration as the
setting No.1
Rn
*1
RnP
*2
RnSF
*2
SM1240
to
SM1249
Data logging setting No.4 Same configuration as the
setting No.1
Data configuration is the same as the
setting No.1 (SM1210 to SM1219).
Same configuration as the
setting No.1
Rn
*1
RnP
*2
RnSF
*2
SM1250
to
SM1259
Data logging setting No.5 Same configuration as the
setting No.1
Data configuration is the same as the
setting No.1 (SM1210 to SM1219).
Same configuration as the
setting No.1
Rn
*1
RnP
*2
RnSF
*2
SM1260
to
SM1269
Data logging setting No.6 Same configuration as the
setting No.1
Data configuration is the same as the
setting No.1 (SM1210 to SM1219).
Same configuration as the
setting No.1
Rn
*1
RnP
*2
RnSF
*2
No. Name Data stored Details Set by (setting timing) CPU
To Next Page
Loading...
