7 - 1 7 - 1
MELSEC-Q
7 APPLICATION FUNCTIONS
7 APPLICATION FUNCTIONS
When applying the program examples introduced in this chapter to the actual system,
make sure to examine the applicability and confirm that it will not cause system control
problems.
Communicating with intelligent function module · · · · · · · · · · · · · · · · · · ·
RAS functions
Automatic return function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Loop back function (Optical loop system) · · · · · · · · · · · · · · · · · · · · · · · ·
Station detach function (Coaxial bus systems) · · · · · · · · · · · · · · · · · · · ·
Transient transmission enabled even at CPU module error · · · · · · · · · ·
Checking the transient transmission abnormal direction time · · · · · · · ·
Diagnostic functions · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Communicating with input/output module · · · · · · · · · · · · · · · · · · · · · · · ·
Basic
functions
Cyclic transmission function
(Periodic communication)
Application
functions
Dedicated link
instructions
Transient transmission function
(Non-periodic communication)
Reading writing remote I/O station intelligent function
module buffer memory (REMFR/REMTO) · · · · · · · · ·
Device test for remote I/O station · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Remote I/O station system monitor · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Multiplex transmission function (Optical loop system) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Return sequence station number setting function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Stopping/restarting the cyclic transmission and stopping link refreshing (Network test) · · · · · · · · · · · · · · · · ·
Reserved station function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
I/O assignment function · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Interrupt settings · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Output reset function for communication errors · · · · · · · · · · · · · · · · · · ·
Section 3.2.1 (2)
Section 3.2.1 (1)
Section 3.2.2 (2)
Section 3.2.2 (3)
Section 3.2.2 (4)
Section 3.2.2 (5)
Section 3.2.2 (6)
Section 3.2.2 (7)
Section 3.2.2 (1)
Section 7.1.1 (1)
Section 7.3
Section 7.2
Section 7.4
Section 7.5
Section 7.10
Section 7.9
Section 7.6
Section 7.8
Section 7.7
Chapter 3
Chapter 7
Multiplexed remote master function (QnPHCPU only) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Network diagnostics (Network monitor) · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
Section 8.1
Configuring a redundant power supply on a remote I/O station · · · · · · ·
Online module change on a remote I/O station · · · · · · · · · · · · · · · · · · ·
Section 3.2.2 (8)
Section 3.2.2 (9)
Multiplexed remote master function for redundant system (QnPRHCPU only) · · · · · · · · · · · · · · · · · · · · · · ·
Section 7.12
Section 7.11
Remote password · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·· · · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
In the application functions, there are executable functions that can be used by
setting the parameters to either the remote master station or remote I/O station.
It is possible to confirm whether the parameters are set to either the remote master
station or remote I/O station by using the table on the heading for each function.
Master
Remote
Remote I/ O station
Remote master station
No need to set
Needs to be set
7