NETGEAR GS716T User Manual

116
GS716T and GS724T Gigabit Smart Switches
To configure IGMP Snooping interface settings:
1. To configure IGMP Snooping settings for a physical port, click PORTS.
2. To configure IGMP Snooping settings for a Link Aggregation Group (LAG), click LAGS.
3. To configure IGMP Snooping settings for both physical ports and LAGs, click ALL.
4. Select the check box next to the port or LAG to configure. You can select multiple ports and
LAGs to apply the same setting to the selected interfaces. Select the check box in the
heading row to apply the same settings to all interfaces.
5. Configure the IGMP Snooping values for the selected port(s) or LAG(s):
• Admin Mode. Use the menu to enable or disable the administrative mode of IGMP
snooping on the selected interface(s). The default is Disable.
• Host Timeout. Specify the amount of time you want the switch to wait for a report for
a particular group on a particular interface before it deletes that interface from the
group. Enter a value between 2 and 3600 seconds. The default is 260 seconds.
• Max Response Time. Specify the amount of time you want the switch to wait after
sending a query on an interface because it did not receive a report for a particular
group on that interface. Enter a value greater or equal to 1 and less than the Host
Timeout, in seconds. The default is 10 seconds.
• MRouter Timeout. Specify the amount of time you want the switch to wait to receive
a query on an interface before removing it from the list of interfaces with multicast
routers attached. Enter a value between 0 and 3600 seconds. The default is 0
seconds. A value of zero indicates an infinite timeout; no expiration.
• Fast Leave Admin Mode. Select the Fast Leave mode for a particular interface from
the menu. The default is Disable.
6. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
7. If you make any configuration changes, click Apply to apply the new settings to the switch.
Configuration changes take effect immediately.

NETGEAR GS716T Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Stackable	-
Certification	CE, FCC, VCCI, EN, C-Tick, CCC, CSA, UL/cUL, IEC
Product color	Blue
LED indicators	Activity, Link, Power
SFP module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1as, IEEE 802.1s, IEEE 802.1v, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 100BASE-T, 1000BASE-T
Noise level	0 dB
Mean time between failures (MTBF)	567680 h
DHCP features	DHCP client
Security algorithms	802.1x RADIUS, HTTPS, SSL/TLS
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	14.4 W
MAC address table	16000 entries
Number of static routes	32
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC
Supported network protocols	IP

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2570 g