NETGEAR GS716T User Manual

213
GS716T and GS724T Gigabit Smart Switches
• Destination MAC. Requires an Ethernet frame’s destination port MAC address to
match the address listed here. Enter a MAC address in this field. The valid format is
xx:xx:xx:xx:xx:xx.
• Destination MAC Mask. If desired, enter the MAC Mask associated with the
Destination MAC to match. The MAC address mask specifies which bits in the
destination MAC to compare against an Ethernet frame. Use Fs and zeros in the MAC
mask, which is in a wildcard format. An F means that the bit is not checked, and a
zero in a bit position means that the data must equal the value given for that bit. For
example, if the MAC address is aa:bb:cc:dd:ee:ff, and the mask is 00:00:ff:ff:ff:ff, all
MAC addresses with aa:bb:xx:xx:xx:xx result in a match (where x is any hexadecimal
number). A MAC mask of 00:00:00:00:00:00 matches a single MAC address.
• EtherType Key. Requires a packet’s EtherType to match the EtherType you select.
Select the EtherType value from the drop down menu. If you select User Value, you
can enter a custom EtherType value.
• EtherType User Value. This field is configurable if you select User Value from the
EtherType drop down menu. The value you enter specifies a customized Ethertype to
compare against an Ethernet frame. The valid range of values is 0x0600–0xFFFF.
• Source MAC. Requires a packet’s source port MAC address to match the address
listed here. Enter a MAC address in the this field. The valid format is
xx:xx:xx:xx:xx:xx.
• Source MAC Mask. If desired, enter the MAC mask for the source MAC address to
match. Use Fs and zeros in the MAC mask, which is in a wildcard format. An F means
that the bit is not checked, and a zero in a bit position means that the data must equal
the value given for that bit. The valid format is xx:xx:xx:xx:xx:xx. A MAC mask of
00:00:00:00:00:00 matches a single MAC address.
• VLAN. Requires a packet’s VLAN ID to match the ID listed here. Enter the VLAN ID to
apply this criteria. The valid range is 1–4093.
3. Click Cancel to cancel the configuration on the screen and reset the data on the screen to
the latest value of the switch.
4. To delete a rule, select the check box associated with the rule and click Delete.
5. To change a rule, select the check box associated with the rule, change the desired fields
and click Apply.

NETGEAR GS716T Specifications

General

Switch type	Managed
Switch layer	L3
Quality of Service (QoS) support	Yes
Stackable	-
Certification	CE, FCC, VCCI, EN, C-Tick, CCC, CSA, UL/cUL, IEC
Product color	Blue
LED indicators	Activity, Link, Power
SFP module slots quantity	2
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	16
Number of VLANs	256
Networking standards	IEEE 802.1D, IEEE 802.1as, IEEE 802.1s, IEEE 802.1v, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 100BASE-T, 1000BASE-T
Noise level	0 dB
Mean time between failures (MTBF)	567680 h
DHCP features	DHCP client
Security algorithms	802.1x RADIUS, HTTPS, SSL/TLS
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	14.4 W
MAC address table	16000 entries
Number of static routes	32
Operating altitude	0 - 3000 m
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Cables included	AC
Supported network protocols	IP

Weight and Dimensions

Depth	204 mm
Width	440 mm
Height	43 mm
Weight	2570 g