Item register
A
Accessibility, electrical connection, 20
Accessories, 62
Adjusting ventilation, 18
Alarm, 60
Assembly, 8
B
Back button, 34
C
Cable lock, 20
Cold and hot water, 16
Commissioning and adjusting, 30
Filling and venting, 30
Preparations, 30
Start guide, 31
Start-up and inspection, 31
Connecting accessories, 29
Connecting cold and hot water, 16
Connecting current sensors, 26
Connecting external operating voltage for the control system, 22
Connecting the climate system, 16
Connections, 21
Contact for activation of fan speed, 28
Contact for activation of “external adjustment", 28
Contact for activation of “temporary lux", 27
Contact for external tariff blocking, 27
Contact information, 7
Control, 34, 38
Control - Introduction, 34
Control - Menus, 38
Control - Introduction, 34
Display unit, 34
Menu system, 35
Control knob, 34
Control - Menus, 38
Menu 1 - INDOOR CLIMATE, 38
Menu 2 - HOT WATER, 44
Menu 3 - INFO, 46
Menu 4 - HEAT PUMP, 47
Menu 5 - SERVICE, 52
D
Delivery and handling, 8
Assembly, 8
Installation area, 8
Removing parts of the insulation, 9
Removing the covers, 9
Supplied components, 9
Transport, 8
Dimensions and pipe connections, 15
Dimensions and setting-out coordinates, 63
Display, 34
Display unit, 34
Back button, 34
Control knob, 34
Display, 34
OK button, 34
Status lamp, 34
Switch, 34
Disturbances in comfort, 60
Alarm, 60
Manage alarm, 60
Troubleshooting, 60
Draining the climate system, 56
Draining the hot water heater, 56
E
Electrical addition - maximum output, 24
Electrical circuit diagram, 70
3x230V, 76
Electrical connections, 19
Accessibility, electrical connection, 20
Cable lock, 20
Connecting accessories, 29
Connecting external operating voltage for the control sys-
tem, 22
Connections, 21
Electrical addition - maximum output, 24
External connection options, 26
General, 19
Load monitor, 25
Miniature circuit-breaker, 19
NIBE Uplink™, 26
Optional connections, 25
Outdoor sensor, 22
Output locking, 24
Power connection, 21
Removing the cover, base board, 20
Removing the cover, immersion heater circuit board, 20
Removing the hatch, input circuit board, 20
Room sensor, 23
Settings, 24
Standby mode, 25
Temperature limiter, 19
Electrical wiring diagram
3x400V, enamel and stainless steel, 70
Exhaust air duct, 18
External connection options, 26
Contact for activation of fan speed, 28
Contact for activation of “external adjustment", 28
Contact for activation of “temporary lux", 27
Contact for external tariff blocking, 27
Possible selection for AUX inputs, 26
Possible selection for AUX output (potential free variable re-
lay), 28
Switch for "Smart Grid ready", 27
Switch for external blocking of addition and/or compressor, 26
Switch for external blocking of heating, 27
F
Filling and venting, 30
Filling the climate system, 30
Filling the hot water heater, 30
Venting the climate system, 30
Filling the climate system, 30
Filling the hot water heater, 30
H
Handling, 2
Heating medium side, 16
Help menu, 31, 37
I
Important information, 2
Safety information, 2
Inspection of the installation, 6
Installation alternative, 17
Connecting hot water circulation, 17
Extra hot water heaters, 17
Two or more climate systems, 17
Water heater with immersion heater, 17
Installation area, 8
M
Manage alarm, 60
NIBE™ F370Chapter 13 | Item register82
13 Item register
To Next Page
Loading...
Need help?
General
