Nibe FIGHTER 1140 - Starting and Checking

Commissioning and adjusting
33
FIGHTER 1140
1. Set the switch (8) to 1.
2. Adjust the heating curve offset knob so there is no
heating requirement.
3. Select “Service” in menu 8.1.1.
4. Select “On” in menu 9.2.4.
5. Select “On” in menu 9.2.12. The brine pump runs
continuously for 10 days, and then returns to nor-
mal operations.
6. Check that the brine and heat medium systems
are vented.
7. Check that brine and heat medium pumps are
operational. If necessary help the pumps to start.
8. Check that the brine temperatures in menu 5.0
correspond with the ground/rock temperature,
which indicate brine flow.
9. Select “Off” in menu 9.2.4.
10. Select the spring/autumn operating mode
with the operating mode button.
11. Adjust the heating curve offset knob so there is a
heating requirement. The compressor will start.
12. If the heat pump is a FIGHTER 1140-12, 15, 17,
check the direction of rotation at start-up of
the compressor.
See section rotation check FIGHTER.
13. Read the brine temperatures in menu 5.0. The dif-
ference between these two temperatures should
be 2—5 °C when the system has come into bal-
ance. Adjust the flow with the knob on the brine
pump (35). A high difference indicates a low brine
flow. A low difference indicates a high brine flow.
The pump is
adjustable to adjust
brine flow.
LEK
G
R
U
N
D
F
O
S
T
y
p
e
U
P
S
2
5
-
6
0
1
3
0
P
/
N
:
5
9
5
2
6
4
4
7
2
3
0
V
-
H
E
J
S
A
N
P
C
;
0
0
1
7
N
I
B
D
K
5
0
H
z
I
P
4
4
T
F
1
1
0
C
l
a
s
s
H
M
a
x
.
1
0
b
a
r
2
.
5
u
F
4
5
0
.
2
0
6
50
.
3
0
9
0
0
.
4
0
1
m
(
A
)
P
,
(
W
)
The pump is
adjustable to adjust
heat medium flow.
15. Set the date and time in menu 7.1 and 7.2.
16. Fill in the commissioning report on page 2.
17. Select the auto operating mode using the
operating mode button.
18. Set the control system according to the needs of
the property. See section “Settings - Heating con-
trol system”.
14. Check the flow temperature on menu 2.0 and
return temperature on menu 2.7. The difference
between these two temperatures, with floating
condensing, should be 5 - 10 °C when the house
is being heated without additional heat. Adjust the
flow with the knob on the heating medium pump
(16). A high difference could depend on a low heat
medium flow. A low difference indicates a high
heat medium flow.
Starting and checking
NOTE!
The compressor must not be forced to
start with periods shorter that 1 start
per 15 minutes.
LE
K
1
2
LEK
G
R
U
N
D
F
O
S
T
y
p
e
U
P
S
2
5
-
6
0
1
3
0
P
/
N
:
5
9
5
2
6
4
4
7
2
3
0
V
-
H
E
J
S
A
N
P
C
;
0
0
1
7
N
I
B
D
K
5
0
H
z
I
P
4
4
T
F
1
1
0
C
l
a
s
s
H
M
a
x
.
1
0
b
a
r
2
.
5
u
F
4
5
0
.
2
0
6
5
0
.
3
0
9
0
0
.
4
0
1
m
(
A
)
P
,
(
W
)
FIGHTER 1140 5-10 kW
FIGHTER 1140 12-17 kW