4 Commissioning
BU 0240 en-US-4920 59
Details of DIP switch S1: 5/4 and 3
Explanation: (values underlined in brackets) = (relevant parameter/source of function), e.g.: Parameter (P420[01])
{curly brackets} = {function} e.g.: {01} "Enable right"
* Default setting
** only if present (devices without "safe stop" function)
*** only with SK 2x5E
Explanation: See table above
Note:
The functions of potentiometers*** P1 and P2 correspond to those of devices without an AS interface (see table above).
With DIP switches 5 and 4 in the OFF position (default setting), the digital inputs are also active. The functions then correspond to those of devices
without an AS interface (table above). In all other DIP switch combinations the functions of the digital inputs are deactivated.
ASi OUT1 and ASi OUT2 loop the signal level (High/Low) of digital inputs 1 and 2.
Pos: 24 1 /Allg emein/ Allg emeing ültig e Mod ule/---------Sei tenum bruc h k omp akt --------- @ 13\mod_1476369695906_0.docx @ 2265496 @ @ 1
Applies to devices SK 20xE, SK 21xE (without on-board AS interface)
DIP Functions as per the list of digital functions (P420)
Functions as per the list of
analog functions (P400)
5 4 3
off off off
P420 [01]*{01}
"Enable R“
P420 [02]*{02}
"Enable L“
{04} "fixed freq 1"
=5 Hz (P465[01])
{05} "fixed freq 2"
=10 Hz (P465[02])
{01} "F
P400 [02]*
{15} "ramp"
off on off
{01} "Enable R" {02} "Enable L"
{12} "Quit" {05} "F max" {04} "F min"
on on off
{50} "F Arr Bit0"
=5Hz (P465[01])
{51} "F Arr Bit1"
=10 Hz (P465[02])
{52} "F Arr Bit2"
=20 Hz (P465[03])
{53} "F Arr Bit3"
=35 Hz (P465[04])
{05} "F max" {15} "Ramp"
off off on
The functions of the digital inputs are inactive (control via system bus) but the settings
entered in the parameters (P420 [01 … 04]) for functions designated with ..² in the
function list (e.g.: {11}²= "quick stop") result in the activation of the correspondingly
parameterized input.
P400 [01]
{01} "F
setpoint"
P400 [02]
{15} "ramp"
P420 [01]
no function
P420 [02]
no function
P420 [03]
{04} "fixed freq1"
=5 Hz (P465[01])
P420 [04]
{05} "fixed freq2"
=10 Hz (P465[02])
off on on
"Encoder track A" "Encoder track B" {01} "Enable R"
{05} "F max"
on off on
{01} "Enable R" {10} "Block"
{05} "F max"
on on on
=10 Hz (P465[02])
=20 Hz (P465[03])
=35 Hz (P465[04])
{05} "F max" {15} "Ramp"
Applies to devices SK 22xE, SK 23xE (without AS interface on board)
DIP Functions as per the list of digital functions (P420)
Functions as per the list of digital outputs
(P434)
5 4 3
off off off
P480 [01]*{01}
"Enable R“
P480 [02]*{02}
"Enable L“
"Fixed freq. 1"
P480 [04]*{12}
"Quit"
P481 [01]*
{07} "Error"
P481 [02]*
{18} "Ready"
"DigIn1" "DigIn2"
off on off
freq. 1"=5 Hz
freq. 2"=10 Hz
freq. 3"=20 Hz
freq. 4"=35 Hz
{07} "Error" {18} "Ready" "DigIn1" "DigIn2"
on off off
{47} "Freq. +" {48} "Freq. -" {07} "Error" {18} "Ready" "DigIn1" "DigIn2"
on on off
{51} "F Arr B1"
=10 Hz (P465[02])
{52} "F Arr B2"
=20 Hz (P465[03])
{53} "F Arr B3"
=35Hz (P465[04])
{07} "Error" {18} "Ready" "DigIn1" "DigIn2"
off off on
The functions of the ASI-In bits are inactive (control via system bus) but
the settings entered in the parameters (P480 [01 … 04]) for functions
designated with ..² in the function list (e.g.: {11}²= "quick stop") result in
the activation of the correspondingly parameterized bit
P481
[01]{07}
"Error"
P481
[02]{18}
"Ready"
"DigIn1" "DigIn2"
P480 [01] no
function
P480 [02]
no function
[03]{04}
"Fixed freq.
1"
=5 Hz
P480 [04]{12}
"Quit"
off on on
{14} "Remote
control"
freq. 1"=5 Hz
freq. 2"=10 Hz
freq. 3"=20 Hz
{07} "Error" {18} "Ready" "DigIn1" "DigIn2"
on off on
{47} "Freq. +"
{48}
"Freq. -"
{07} "Error" {18} "Ready" "DigIn1" "DigIn2"
on on on
{50} "F Arr B0"
=5Hz (P465[01])
{51} "F Arr B1"
=10 Hz (P465[02])
{52} "F Arr B2"
=20Hz (P465[03])
{07} "Error" {18} "Ready" "DigIn1" "DigIn2"
To Next Page
Loading...
Need help?
General
