Nord Drivesystems NORDAC FLEX SK 215E Series Brief Instructions

6 Operating status messages
BU 0240 en-US-4920 75
Pos: 64 5 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen @ 3\mod_1361802708455_14638. docx @ 59828 @ 2 @ 1
6.1 Display of messages
Pos: 64 6 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebs zus ta nd/D ars tell ung der Mel du nge n - LED A nzei gen @ 3\m od_1361796228478_14638.docx @ 59714 @ 5 @ 1
LED displays
The device status is indicated by integrated and externally visible status LEDs included in the factory
default kit. Depending on the device model, this is a two-color LED (DS = Device State) or two
monochromatic LEDs (DS Device State and DE = Device Error).
Meaning: Green indicates the standby status and the presence of mains voltage. During
operation an increasingly rapid flashing code indicates the degree of overload
of the device output.
Red
indicates the presence of an error by flashing with a frequency which
corresponds to the number code of the fault. This flashing code indicates the
error groups (e.g.: E003 = 3x flashes).
Pos: 64 7 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Dars tell ung der Meldu ngen - Si mpl eBox / C on trolB ox Anzei g e [SK xxx E, SK 5 xxP ] @ 3\mod_1361801795294_14638. docx @ 59822 @ 5 @ 1
SimpleBox display
The SimpleBox displays a fault with its number and the prefix "E". In addition, the current fault can be
displayed in array element [-01] of parameter (P700) . The last fault messages are stored in parameter
P701. Please refer to parameters P702 to P706/P799 for further information on device status at the
time the fault occurs.
If the cause of the fault is no longer present, the error display in the SimpleBox flashes and the error
can be acknowledged with the Enter key.
In contrast, warning messages are prefixed with "C" ("Cxxx") and cannot be acknowledged. They
disappear automatically when the reason for them is no longer present or the device has switched to
the Fault state. Display of the message is suppressed if the warning appears during parameterization.
The current warning message can be displayed in detail at any time in array element [-02] of
parameter (P700).
The reason for an existing disabled switch on cannot be displayed with the SimpleBox.
Pos: 64 8 /Anlei tu nge n/El ektr onik /FU un d St art er/6 . M eld ung en z um B etr iebs zus ta nd/D ars tell ung der Mel du nge n - Par ame ter Box - Anz eige @ 3\mod_1361801566355_14638.docx @ 59780 @ 5 @ 1
Parameter Box display
The Parameter Box displays messages in plain text.
Pos: 64 9 /Anlei tung en/El ektr onik/FU und Star ter/6 . Meld ungen zum Betr iebsz usta nd/Diag nos e LEDs/D iag nose LED s am Ger ät (Über schri ft+) [S K 1xxE, SK 2xxE, SK xxxE-FD S] @ 1\mod_1343201905326_14638.docx @ 36936 @ 2 @ 1
6.2 Diagnostic LEDs on device
The device generates operating status messages. These messages (warnings, errors, switching
statuses, measurement data) can be  3.1.1 "Use of control and parameterization units"displayed
with parameterization tools (e.g. Parameter Box) (parameter group P7xx).
To a limited extent, the messages are also indicated via the diagnostic and status LEDs.
Pos: 65 0 /Allg emein/ Allg emeing ültig e Mod ule/---------Sei tenum bruc h k omp akt --------- @ 13\mod_1476369695906_0.docx @ 2265496 @ @ 1

Nord Drivesystems NORDAC FLEX SK 215E Series Specifications

General

Brand	Nord Drivesystems
Model	NORDAC FLEX SK 215E Series
Category	Inverter
Language	English