Oceanic Dive Computer Pro Plus 2

To Next Page

To Previous Page

Be a -

RESPONSIBLE DIVER

at all times.

Main Page

Contents3
Product View and Components6
Features and Displays7
Interactive Control Console8
Tissue Loading Bar Graph9
Oxygen Accumulation Bar Graph (O2BG)10
Variable Ascent Rate Indicator (VARI)10
Air Time Remaining Bar Graph (ATRBG)11
Dive Time Remaining11
Alpha/Numeric Displays12
Cylinder Pressure/Depth Display12
Time and Date/Temperature Display13
Audible Alarm14
LED Warning Light14
A Single Short Beep14
Situations that will Sound the Alarm, if It Is Turned on15
The 10 Second Continuous Tone will be Followed by a 5 Second Steady Beep15
Smartglo Backlight16
Power Supply16
Battery Indicator16
Low Battery Condition17
FO2 Mode18
FO2 50% Default19
FO2 Default off20
Activation and Setup21
Backup Activation22
Diagnostic Mode22
Surface Mode23
Set Modes/Mode Access Timing24
Entering Settings - Set Mode 125
To Set - FO225
To Set - Max Depth Alarm26
To Set - Elapsed Dive Time Alarm27
PC Interface28
To Download Data (While in the Surface Mode)28
Entering Settings - Set Mode 229
To Set Units of Measure29
To Set Hour Format30
To Set Time31
To Set Date (after Setting Time)32
To Set Audible Alarm (While in the Surface Mode)33
To Set Maximum Tissue Loading Bar Graph Alarm34
To Set Air Time Remaining Bar Graph Alarm35
To Set Turn Pressure Alarm36
To Set - End Pressure Alarm37
To Set Dive Time Remaining Alarm38
To Set Maximum PO2 Alarm39
To Set - FO2 50% Default40
To Set Backlight Duration41
To Set PC Sampling Rate42
To Set User Set Digital Gauge Mode43
To Set Water Activation44
Plan and Dive Modes45
Pre Dive Planning Sequence46
To Access the Pre Dive Planning Sequence47
Nitrogen/Oxygen Control47
Oxygen Accumulation Bar Graph49
Variable Ascent Rate Indicator49
Air Time Remaining Bar Graph50
Control of Displays50
No Decompression Dive Mode51
No Decompression Dive Mode - Secondary Display/Safety Stop53
Decompression Dive Mode54
Total Ascent Time54
Entry into Deco Mode54
Managing Decompression Stops55
Decompression Dive Mode Main Display55
Violation Modes/Conditional Violation Mode57
Delayed Violation Mode58
Immediate Violation Mode and Gauge Mode60
High PO2 Dive Mode62
PO2 Warning/Alarm62
High Oxygen Accumulation63
User Set Digital Gauge Mode64
Post Dive Modes65
Post Dive Surface Mode66
Transition Period66
Log Mode (During Transition Period)67
After the Transition Period (the First 2 Hours)68
LOG Mode70
Button Control in Log Mode70
To Access the Log Mode and View the First Screen71
To View the Second Screen of the Log71
After the First 2 Hours72
To View the Third Screen of the Log (Oxygen Data)72
To Access the First Screen of the Previous Dive's Log72
Wet Contacts73
Fly Mode/Desaturation Mode73
Downloading Data to a PC/PC Interface74
Simulator (Demo) Mode75
Simulator Mode76
Access and Setup76
Set Demo Gauge76
Set Demo Calibration/Pressure on and off77
Demo Dive Mode78
Set Demo FO278
Descending79
Dive Mode Setup79
Time Acceleration79
Ascending80
Surfacing from a Simulated Dive81
Demo Surface Mode81
General83
Care and Cleaning84
Inspections and Service84
To Obtain Service85
To Return Your Pro Plus 2 to Oceanic85
Battery Replacement86
Hot Swap86
Battery Removal87
Moisture in the Battery Compartment88
Battery Installation/Orientation88
O-Ring Installation88
Battery Hatch Installation/Inspection89
Specifications90
Can be Used as90
No Decompression Model90
Operational Modes (Surface)90
Operational Modes (Dive)91
Display Range/Resolution92
Bar Graphs93
Operational Performance93
Inspection/Service Record97
Reset Feature/Procedure99

Oceanic Dive Computer Pro Plus 2 - Page 82

Table of Contents

Related product manuals