Oceanic GEO 2 - User Manual

Explains the various icons used on the dive computer display.

Details the function and use of the dive computer's four control buttons.

Describes the specific button presses and holds for navigating menus.

Details the display and behavior when battery level is low while on the surface.

Explains display and function changes when battery is low during a dive.

Details how to navigate and select options within the Watch Menu.

Shows altitude information in Watch mode, including temperature and date format.

Shows the remaining countdown time or if the timer is complete or off.

Explains how to set the hour and minute values for the countdown timer.

Configures the display order for Month and Day digits.

Configures the hour display for 12-hour (AM/PM) or 24-hour format.

Chooses between Home or Away time to be displayed as the main Watch Time.

Sets an hour-based differential for the Dual Time display.

Directly changes the Time of Day for the selected Watch Default Time.

Sets the year, month, and day for the device, independent of date format.

Displays Surface Interval time, Time of Day, dive number, and system icons.

Shows Surface Interval, last dive data, max depth, and elapsed dive time.

Displays temperature and altitude information.

Shows current O2%, PO2 alarm value, Gas 1 FO2, and system icons.

Shows countdown timers for Time to Fly and Time to Desaturate.

Allows viewing of recorded dive data, including date, time, and dive number.

Presents pre-dive Surface Interval and Total Ascent Time data for a dive.

Shows minimum dive temperature and altitude information.

Displays end-of-dive O2%, highest PO2, and gas settings.

Entry point for configuring FO2 settings for Nitrox diving.

Configures the Fraction of Oxygen (FO2) for the first gas mix.

Configures the Fraction of Oxygen (FO2) for the second gas mix.

Sets the default FO2 value for calculations, typically 50%.

Configures depth-based alarms for dive modes.

Sets an alarm based on the Elapsed Dive Time during a dive.

Configures the TLBG alarm for nitrogen loading status.

Sets an alarm based on the remaining dive time.

Configures the alarm for partial pressure of oxygen (PO2) levels.

Enables or disables automatic dive mode activation upon water immersion.

Selects between Imperial (FT) and Metric (M) units for display.

Enables or disables the Deep Stop feature during No Deco dives.

Configures the Safety Stop depth and timer settings.

Selects between DSAT or PZ+ algorithms for dive calculations.

Adjusts dive time calculations for increased safety margins.

Configures how long the display backlight remains active.

Determines the frequency of data sampling for logging.

Represents nitrogen loading status and deco conditions.

Adjusts dive time calculations for increased safety margins.

Maximum time allowed at current depth before entering deco.

Displays Time of Day and Temperature.

Shows Nitrox specific data: NX icon, %O2, PO2, and Gas settings.

Displays Deep Stop depth and time settings before activation.

Shows current depth, Ascent Time, Stop Depth, and TLBG.

Displays dive depth, Ascent Time, Max Depth, EDT, and TLBG.

Shows Time of Day and Temperature.

Displays Nitrox specific data: NX icon, Gas, %O2, PO2, and FO2.

Shows depth, VIO, EDT, and ascent rate in VGM mode.

Describes VGM display for 10 minutes post-dive or after a delayed violation.

Explains PO2 display behavior and alarms when in decompression mode.

Displays last dive's SI, max depth, and elapsed dive time.

Shows temperature and altitude information.

Displays max depth and elapsed dive time.

Shows Time of Day and Temperature.

Displays last dive's SI, max depth, and elapsed dive time.

Shows temperature and altitude information.

Shows the remaining countdown time or if the timer is complete or off.

Sets the first depth alarm for Free Dive Mode.

Lists settings in Free Mode that can be changed via Norm Mode's Set U menu.

Details the steps for safely removing the battery from the unit.

Ensures the display is clear and sets initial parameters after installation.

Highlights crucial safety precautions for free diving activities.

Details the segment zones for the Tissue Loading Bar Graph (TLBG).

Defines the segments and speeds for the Variable Ascent Rate Indicator.

Explains the various icons used on the dive computer display.

Details the function and use of the dive computer's four control buttons.

Describes the specific button presses and holds for navigating menus.

Details the display and behavior when battery level is low while on the surface.

Explains display and function changes when battery is low during a dive.

Details how to navigate and select options within the Watch Menu.

Shows altitude information in Watch mode, including temperature and date format.

Shows the remaining countdown time or if the timer is complete or off.

Explains how to set the hour and minute values for the countdown timer.

Configures the display order for Month and Day digits.

Configures the hour display for 12-hour (AM/PM) or 24-hour format.

Chooses between Home or Away time to be displayed as the main Watch Time.

Sets an hour-based differential for the Dual Time display.

Directly changes the Time of Day for the selected Watch Default Time.

Sets the year, month, and day for the device, independent of date format.

Displays Surface Interval time, Time of Day, dive number, and system icons.

Shows Surface Interval, last dive data, max depth, and elapsed dive time.

Displays temperature and altitude information.

Shows current O2%, PO2 alarm value, Gas 1 FO2, and system icons.

Shows countdown timers for Time to Fly and Time to Desaturate.

Allows viewing of recorded dive data, including date, time, and dive number.

Presents pre-dive Surface Interval and Total Ascent Time data for a dive.

Shows minimum dive temperature and altitude information.

Displays end-of-dive O2%, highest PO2, and gas settings.

Entry point for configuring FO2 settings for Nitrox diving.

Configures the Fraction of Oxygen (FO2) for the first gas mix.

Configures the Fraction of Oxygen (FO2) for the second gas mix.

Sets the default FO2 value for calculations, typically 50%.

Configures depth-based alarms for dive modes.

Sets an alarm based on the Elapsed Dive Time during a dive.

Configures the TLBG alarm for nitrogen loading status.

Sets an alarm based on the remaining dive time.

Configures the alarm for partial pressure of oxygen (PO2) levels.

Enables or disables automatic dive mode activation upon water immersion.

Selects between Imperial (FT) and Metric (M) units for display.

Enables or disables the Deep Stop feature during No Deco dives.

Configures the Safety Stop depth and timer settings.

Selects between DSAT or PZ+ algorithms for dive calculations.

Adjusts dive time calculations for increased safety margins.

Configures how long the display backlight remains active.

Determines the frequency of data sampling for logging.

Represents nitrogen loading status and deco conditions.

Adjusts dive time calculations for increased safety margins.

Maximum time allowed at current depth before entering deco.

Displays Time of Day and Temperature.

Shows Nitrox specific data: NX icon, %O2, PO2, and Gas settings.

Displays Deep Stop depth and time settings before activation.

Shows current depth, Ascent Time, Stop Depth, and TLBG.

Displays dive depth, Ascent Time, Max Depth, EDT, and TLBG.

Shows Time of Day and Temperature.

Displays Nitrox specific data: NX icon, Gas, %O2, PO2, and FO2.

Shows depth, VIO, EDT, and ascent rate in VGM mode.

Describes VGM display for 10 minutes post-dive or after a delayed violation.

Explains PO2 display behavior and alarms when in decompression mode.

Displays last dive's SI, max depth, and elapsed dive time.

Shows temperature and altitude information.

Displays max depth and elapsed dive time.

Shows Time of Day and Temperature.

Displays last dive's SI, max depth, and elapsed dive time.

Shows temperature and altitude information.

Shows the remaining countdown time or if the timer is complete or off.

Sets the first depth alarm for Free Dive Mode.

Lists settings in Free Mode that can be changed via Norm Mode's Set U menu.

Details the steps for safely removing the battery from the unit.

Ensures the display is clear and sets initial parameters after installation.

Highlights crucial safety precautions for free diving activities.

Details the segment zones for the Tissue Loading Bar Graph (TLBG).

Defines the segments and speeds for the Variable Ascent Rate Indicator.