Panasonic AG-CPD20P - Write Protection and No Card Errors; File Loading and Administrator Errors

114
115
No. Message Measure
E15763
Write Protect Card found on slot1.
Record cannot be started.
The write-protection switch on the SDHC Memory Card is set to the “LOCK”
position. Slide the write-protection switch away from the “LOCK” position.
E15764
Write Protect Card found on slot2.
Record cannot be started.
E15765
Write Protect Card found on slot3.
Record cannot be started.
E15766
Write Protect Card found on slot4.
Record cannot be started.
E15767
No SDHC Cards found.
Record cannot be started.
No SDHC Memory Card is inserted. Insert an SDHC Memory Card.
E15768
Write Error.
Record cannot be started.
The SDHC Memory Card cannot be written to. Replace the SDHC Memory
Card.
E15769
Card Full.
Record cannot be started.
The following conditions may have occurred.
• There is no space left on the SDHC Memory Card.
• Files contained in one of the SDHC Memory Cards inserted in the SDHC
Memory Card slots 1, 2, 3, and 4 exceed 5,000 les.
Replace the SDHC Memory Card with an SDHC Memory Card with free
capacity, or free up space in the SDHC Memory Card for new data. (free
space of more than 10 MB)
E20801
Recorder reboots by
unrecoverable card ejection error.
Be sure to use the correct procedure to remove and load SDHC Memory
Cards.
E20802
Please reinsert the card or reboot
the system.
Check the SDHC Memory Card and re-insert it, or reboot the recorder.
E20901
Firmware Update FAILED! An error occurred during the update.
• Check whether the update le for the recorder has been correctly copied
to the SDHC Memory Card or USB memory device.
• Reformat the SDHC Memory Card or USB memory device before use.
• Use another USB memory device.
• Check whether there are multiple update les on the SDHC Memory Card
or USB memory device.
• Check whether there are multiple SDHC Memory Cards and/or USB
memory devices containing update les.
• An SDHC Memory Card with a \DATA folder cannot be used for updating.
• A USB memory device containing a folder other than the \WIDKEY folder
cannot be used for updating.
E20911
Microcontroller Update FAILED! An error occurred during the update.
The recorder reboots automatically to restart an update.
Contact your supplier if the problem persists.
E20912
Unsupported Microcontroller
Detected!
The recorder has broken down.
Contact your supplier.
E20921
AG-RCP30 Update FAILED! An error occurred during an update of an AG-RCP30 connected to the
recorder.
The recorder reboots automatically to restart an update.
Contact your supplier if the problem persists.
E20922
Unsupported Control Panel
Detected!
A Remote Control Panel not supported by the recorder was detected.
Disconnect the Remote Control Panel.
E22420
Officer’s information file cannot be
loaded.
The ofcer data le (WID
*****
.TXT) is corrupted. Create a new ofcer’s data le,
save it to a USB memory device and re-register it.
E22421
Since you are not an
administrator, you cannot open
this menu.
You are not registered as an administrator and cannot open this menu. Ask a
registered administrator for assistance.
E22422
Officer’s information file cannot be
loaded.
There is no Ofcer Registration le or it contains the wrong data. Create a
correct Ofcer Registration le (WOFFICER.TXT), copy it to a USB memory
device and reload it.
E22423
Admin’s information file cannot be
loaded.
There is no Administrator Registration le or it contains the wrong data. Create
a correct Administrator Registration le (WADMIN.TXT), copy it to a USB
memory device and reload it.
E22425 Classification list cannot be
loaded.
There is no classify le or the content of the le is incorrect. Copy the
correct classify le (CLASSIFY.TXT) to the USB memory device and
reregister it.
Error Message
(continued)