21
Setting Item Factory Default Value Description
2
Preset2
*
1
Preset 2 setting
Form 1Ch Channel mode setting
Setting: 1Ch, 2Ch, 4Ch-QUAD, 4Ch-PANORAMA, 5Ch-QUAD,
5Ch-PANORAMA, - (preset not used)
Main Sub 2, - Cameras for Main and Sub pictures setting
Setting: 1, - 2, - 3, -
1, 2 1, 3 2, 3
-, 1456 -, 2456 -, 3456
1, 2456 1, 3456 2, 3456
3, 2456
Preset3 Preset 3 setting
Form 2Ch Channel mode setting
Setting: 1Ch, 2Ch, 4Ch-QUAD, 4Ch-PANORAMA, 5Ch-QUAD,
5Ch-PANORAMA, - (preset not used)
Main Sub 1, 2 Cameras for Main and Sub pictures setting
Setting: 1, - 2, - 3, -
1, 2 1, 3 2, 3
-, 1456 -, 2456 -, 3456
1, 2456 1, 3456 2, 3456
3, 2456
Main Resolution/
RecRate
D1 HI Main-picture’s resolution and bit rate settings
Setting: CIF, D1 10, D1 STD, D1 HI
Sub Resolution/
RecRate
D1 HI Sub-picture’s resolution and bit rate settings
Setting: CIF, D1 10, D1 STD, D1 HI
3
Rec/Play Recording and playback settings
PowerOff Time
*
2
AUTO
Time from the SIGNAL turn-off to recorder shut-down (minutes)
Setting :
0 min, 10 min, 20 min, 30 min, 60 min, 90 min, 120 min, 180 min, AUTO
*
3
Init Preset Select PRESET1 Initial Preset setting
*
4
Setting: PRESET1, PRESET2, PRESET3, LAST
*
5
Init VIDEO OUT1 VIDEO_OUT2 Initial through-out video setting
*
4
Setting: CAM1, CAM3, VIDEO_OUT2, LAST
*
5
PowerOn Rec OFF Automatically start recording with power-on
Setting : OFF, ON
Loop Rec OFF Loop recording
Setting : OFF, ON
*
6
Intermittent Rec OFF Intermittent recording
Setting : OFF, ON
Setup
(continued)
(Continued on the next page)
*
1 If the Preset2 or Preset3 setting is canceled on the Video
Allocation screen in Administrator setup, the setting of
Action on the Trigger screen may be changed to NONE.
*
2 Depending on the vehicle, the battery may run out of
power during operation.
*
3 When a PC with the Front-End application or Back-
End application installed is not connected:
Power is turned off immediately. Note, however, that
power is not turned off while data is being exported to a
USB memory device, but is turned off after completion
of data export.
When a PC with Front-End application or a Back-End
application installed is connected:
Power is turned off when control from a Front-End
application or Back-End application is released, when
upload, streaming, administrator setting, or updating
with Back-End application is terminated, or when the
SDHC Memory Card slot is opened.
*
4 Depending on the settings on the Video Allocation screen
in Administrator setup, some items may not be displayed.
*
5 Applies the setting in effect when power was last turned
off. Unless power is turned off properly, the operating state
may not be saved correctly.
*
6 If “Loop Rec” is set to ON, pre-recording and post-
recording do not function.
Playback with the remote control panel is not available
at present. Upgrading is scheduled for the future.
For playback, it is recommended to use the Front-End
application or Back-End Client application.
To Next Page
Loading...
