Panasonic Diga DMR-EX98V - Page 72

72
RQT9090
Changing the unit’s settings
Signal Condition
You can check the quality and strength of digital broadcast signals.
Realign the aerial if you are receiving a poor signal.
When “Signal Condition” is displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [
1 2
CH] to select a digital channel. “D” appears on the
unit’s display.
3 Display the Setup menu again (➡ 71).
Press [
e
,
r
] to select “Signal Condition” and press [OK].
The quality and strength of the signal are shown.
Press [
1 2
CH] to select the channel.
010
010
2 ABC 2W DVB CH
30
RETURN
CH +
CH –
Signal Quality
Signal Strength
Signal Quality
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. “0” means signal strength 0%,
“10” means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplifi cation at your aerial.
y When the signal is weak:
– adjust the position and direction of the aerial.
– adjust the aerial reception with “DVB Manual Tuning” in the Setup
menu (➡ 71).
– check that the current digital broadcast channel is correctly
broadcasting.
DVB Preferred Language
Press [
e
,
r
] to select “DVB Preferred Language” and press [OK].
You can select up to 2 different subtitles
(
For Italy, Spain and Switzerland
) and audio tracks to be used when
audio and subtitles digital broadcasts are received. Select the order
of priority.
If the selected language is not available, then the original language
will be selected.
Multi-Audio
Multi-Audio (alternative)
For Germany
[English] [German] [Italian] [French]
[Spanish]
For Italy, Spain and Switzerland
[English] [German] [Italian] [French]
[Spanish] [Catalan] [Basque] [Galician]
[Corsican]
Subtitle
For Italy, Spain and Switzerland
Subtitle (alternative)
For Italy, Spain and Switzerland
[English] [German] [Italian] [French]
[Spanish] [Catalan] [Basque] [Galician]
[Corsican]
■ Settings for Analogue Services
Press [OK] to show the following settings.
Manual Tuning
You can delete analogue channels and set the analogue channel
details.
Press [OK] to show Manual Tuning screen.
1 ARD 4
2 ZDF 2
3 N3 5
4 HR3 8
5 BR3 10
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
OK
RETURN
SELECT
Manual Tuning
Pos Name Ch Pos Name Ch
Delete
Add
Move
To delete a programme position
Press [
e
,
r
,
w
,
q
] to select a programme position and press the
“Red” button.
Note
y
For Germany
This unit does not support SECAM L, L’.
To change the tuning settings for individual programme
position
1 Press [
e
,
r
,
w
,
q
] to select a programme position and press
[OK].
For Germany For Italy, Spain and Switzerland
901
4
301
RETURN
SELECT
901
4
301
RETURN
SELECT
Manual
Tuning
Pos
Name
Channel
Fine Tuning
Video System
Mono
Title Page
Auto
Auto
Off
ARD
RETURN : leave
Manual
Tuning
Pos
Name
Channel
Fine Tuning
Video System
Audio Mode
Mono
Auto
Auto
BG
ARD
RETURN : leave
Off
Title Page
2 Press [
e
,
r
] to select an item and press [
q
].
Pos Programme position in the table
(You cannot change the programme position.)
Name To enter or change the name of a TV
station
Press [
e
,
r
,
w
,
q
] to enter station name and
press [OK].
If the station name needs a blank space,
select the blank between “Z” and “¼”.
Channel To enter newly available TV stations or
change the channel number of an already
tuned TV station
Press [
e
,
r
] or the numbered buttons to enter
the channel number of the desired TV station.
Wait a few moments until the desired TV
station has been tuned.
After the desired TV station is tuned, press
[OK].
Fine Tuning To obtain the best tuning condition
Press [
e
,
r
] to adjust the best tuning
condition and press [OK].
y Press [
q
] to return to “Auto”.
Video System To select the video system type
Press [
e
,
r
] to select “PAL” or “SECAM” if the
picture lacks colour, and press [OK].
y Auto
This unit automatically distinguishes PAL
and SECAM signals.
y PA L
For receiving PAL signals.
y SECAM
For receiving SECAM signals.
Audio Mode
For Italy, Spain and
Switzerland
To select the audio reception type
If sound quality is poor, press [
e
,
r
] to select
“BG” or “L” and press [OK].
y BG
PAL B.G.H/SECAM B.G
y L
SECAM L, L’
Mono To select the type of sound to be recorded
Press [
e
,
r
] to select “On” if the stereo sound
is distorted due to inferior reception
conditions, or if you want to record the normal
(mono) sound during a stereo, bilingual or
NICAM broadcast, and press [OK].
Title Page To enter the Teletext title page for a
channel
Entering title page number allows the unit to
automatically record programme and station
names.
Press [
e
,
r
] or numbered buttons to enter the
number and press [OK].
y To fi nd the correct title page for the station,
refer to its Teletext TV guide.
RQT9090-LDMR-EX98VEC-EGen.indb72RQT9090-LDMR-EX98VEC-EGen.indb72 2008/04/3021:55:162008/04/3021:55:16