How to fix Panasonic Conference Phone not ringing when a call is received?
If the unit does not ring when a call is received, the ringer may be turned off. Press the indicated button while a call is being received, or change the ringer volume setting.
What to do if I cannot use the Panasonic Conference Phone for PS or PC calls?
If you cannot use the unit for PS or PC calls: * Confirm you are using the correct cable to connect to the device, and that the cable is connected properly. * When the operation mode is set to "USB Audio", you cannot make or receive IP, TEL, PS or PC calls. Change the setting to "Peer to Peer" or "IP-PBX". * Confirm that "PS" or "PC" is shown in the upper-right corner of the display. Press the center function button ([F2]) to change the line if necessary. Make sure the "Line Selection" setting is set to "IP + PS" (for PS calls) or "IP + PC" (for PC calls).
Why can't I record to the SD memory card with my Panasonic Conference Phone?
You might not be able to record to the SD memory card due to several reasons: * The SD memory card may not be compatible with the unit. (SDHC, miniSDHC, and microSDHC memory cards are not compatible with the unit.) * The SD memory card may not be formatted or was not formatted properly. Format SD memory cards for use with this unit in FAT format (FAT16) using a computer. * The SD memory card may not be inserted properly. Make sure that the SD memory card is inserted properly by gently pushing it securely but gently toward the back of the SD memory card slot.
What does 'Memory Full' mean on my Panasonic Conference Phone?
The 'Memory Full' message indicates that the SD memory card cannot be used for recording because it is full. Erase unneeded recordings to free up space.
What does 'Write Protected' mean on my Panasonic Conference Phone?
The 'Write Protected' message indicates that the switch on the side of the SD memory card is in the "LOCK" position. Remove the card, slide the switch to unlock the card, then insert the card again.
How to make settings take effect on Panasonic Conference Phone?
After you change the settings, restart the unit for the changes to take effect.
Why can't I make TEL calls on my Panasonic KX-NT700 IP Phone?
If you cannot make TEL calls on your Panasonic IP Phone, first, ensure that "TEL" is shown in the upper-right corner of the display before dialing. Press the center function button to change the line if necessary. Also, verify that the "Line Selection" setting is set to "IP + TEL", and that the operation mode is not set to "USB Audio". If it is, change it to "Peer to Peer" or "IP-PBX". Finally, ensure that the dial mode matches the type of telephone service you have (tone or pulse).
Why can't I make IP calls on my Panasonic KX-NT700 IP Phone?
If you can't make IP calls on your Panasonic IP Phone, first confirm that "IP" is shown in the upper-right corner of the display before dialing. Press the center function button to change the line if necessary. Make sure you've entered the IP address of the other party correctly. Also, check the "Operation Mode" setting. Change it to "Peer to Peer" for calls made by specifying the IP address, or to "IP-PBX" for intercom and outside calls as a SIP extension. Ensure it is not set to "USB Audio".
Why am I unable to receive TEL calls on my Panasonic IP Phone?
If you are unable to receive TEL calls on your Panasonic IP Phone, ensure that the "Line Selection" setting is set to "IP + TEL". Also, check that the operation mode is not set to "USB Audio". If it is, change the setting to either "Peer to Peer" or "IP-PBX".
Why can't I receive IP calls on my Panasonic IP Phone?
If you cannot receive IP calls on your Panasonic IP Phone, the "Operation Mode" setting might not be correct. Change the setting to "Peer to Peer" if you want to make or receive peer to peer IP calls, or change the setting to "IP-PBX" if you want to make or receive intercom and outside calls as a SIP extension. When the setting is "USB Audio", you cannot make or receive IP calls, so change the setting to "Peer to Peer" or "IP-PBX".
General| Category | IP Phone |
|---|---|
| Protocols | SIP |
| Power over Ethernet | Yes (IEEE 802.3af) |
| Microphones | Built-in |
| Bluetooth | No |
| Operating Temperature | 0 °C to 40 °C |
| Display | LCD |
| Supported Protocols | SIP |
| Audio Codecs | G.711, G.722, G.729 |
| Power Supply | AC Adapter |
| Speakerphone | Yes |
| Headset Jack | Yes |
| Operating Humidity | 10% to 90% (non-condensing) |
To Next Page
