Panasonic PT-EX620 - About Your Projector; Remote Control

Chapter 1 Preparation — About your projector
ENGLISH - 25
About your projector
Remote control
r Bottom
r Top
r Front
For PT-EZ590 / PT-EW650 /
PT-EX620
For PT-EW550 /
PT-EX520
2
1
3
4
6
5 5
7
18
17
19
8
9
10
12
16
15
21
20
22
23
11
14
13
13
24
25
1 Power <v/b> button (v standby/b power on)
Sets the projector to the state where the projector is switched
off (standby mode) when the <MAIN POWER> switch on the
projector is set to <ON> and in the projection mode.
Also starts projection when the power is switched off (standby
mode).
2 Remote control indicator
Blinks if any button in the remote control is pressed.
3 Lens (<FOCUS>, <ZOOM>, <SHIFT>) buttons
Adjusts the projection lens. (x page 52)
4 <MENU> button/<RETURN> button/<ENTER> button/
asqw buttons
Used to navigate through the menu screen. (x page 62)
5 <VOL
- > button/<VOL+> button
Adjusts the volume of the built-in speaker or audio output.
(x page 55)
6 <DEFAULT> button
Resets the content of the sub-menu to the factory default.
(x page 63)
7 Input selection (<RGB1/2>, <DIGITAL LINK>
*1
, <VIDEO>,
<NETWORK>, <HDMI1>, <HDMI2>) buttons
Switches the input signal to project. (x page 51)
(*1 This button is disabled for PT-EW550 and PT-EX520.)
8 Number (<0> ~ <9>) buttons
Used for entering an ID number or a password in a multiple
projectors environment.
9 <ON SCREEN> button
Switches on (display)/off (hide) the on-screen display function.
(x page 55)
10 <ID ALL> button
Used to simultaneously control all the projectors with a
single remote control in a multiple projector environment.
(x page 59)
11 <AUTO SETUP> button
Automatically adjusts the image display position while the
image is projected. (x page 56)
12 <FUNCTION> button
Assigns a frequently used operation as a shortcut button.
(x page 58)
13 <SHUTTER> button/<AV MUTE> button
(<SHUTTER> button is for PT-EZ590, PT-EW650 and
PT-EX620.
<AV MUTE> button is for PT-EW550 and PT-EX520.)
Used when temporarily turning off the image and the audio.
(x page 54)
14 <TEST PATTERN> button
Displays the test pattern. (x page 58)
15 <ID SET> button
Sets the ID number of the remote control in a multiple projector
environment. (x page 59)
16 <ECO> button
Displays the setting screen relating to ECO management.
(x pages 59, 93)
17 <SCREEN ADJ> button
You can correct various types of distortion in a projected image.
(x page 56)
18 <FREEZE> button
Used when pausing the image and turning off the audio.
(x page 55)
19 <P-TIMER> button
Operates the presentation timer function. (x page 58)
20 <D.ZOOM -> button/<D.ZOOM +> button
Zoom in and out the images. (x page 57)
21 <MUTE> button
Used when temporarily turning off the audio. (x page 55)
22 <ASPECT> button
Switches the aspect ratio of the image. (x page 57)
23 <STATUS> button
Displays the projector information. (x pages 59, 92)
24 Remote control signal transmitter
25 Remote control wired terminal
This is the terminal used to connect to the projector via a cable
when the remote control is used as a wired remote control.
(x page 29)