Panasonic TH-50PH9UK - Applicable Signals; Safety Precautions; General Guidelines; Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices

1 Applicable signals 4
2 Safety Precautions
5
2.1. General Guidelines
5
3 Prevention of Electro Static Discharge (ESD) to
Electrostatically Sensitive (ES) Devices
6
4 About lead free solder (PbF)
7
5 Service Hint
8
6 Disassembly
9
6.1. Removal of the Back Cover
9
6.2. Removal of the HU-Board
9
6.3. Removal of the HA-Board
9
6.4. Removal of the Slot Block
9
6.5. Removal of the J-Board
10
6.6. Removal of the HX-Board
10
6.7. Removal of the PB-Board
10
6.8. Removal of the DA-Board
11
6.9. Removal of the P-Board
11
6.10. Removal of the D-Board
12
6.11. Removal of the H3-Board (L, R)
12
6.12. Removal of the SU-Board and the SD-Board
12
6.13. Removal of the SC-Board
13
6.14. Removal of the SS2-Board and the SS3-Board
13
6.15. Removal of the SS-Board
13
6.16. Removal of the C1, C2, C3, C4, C5 and the C6-Board
13
6.17. Removal of the S1-Board
15
6.18. Removal of the Fan
15
6.19. Removal of the Escutcheon
16
6.20. Removal of the V1-Board and the V2-Board
16
6.21. Removal of the Plasma Panel
17
7 Location of Lead Wiring
20
7.1. Location of Lead Wiring (1)
20
7.2. Location of Lead Wiring (2)
21
7.3. Location of Lead Wiring (3)
22
7.4. Location of Lead Wiring (4)
22
8 Adjustment Procedure
23
8.1. Driver Set-up
23
8.2. Initialization Pulse Adjust
24
8.3. P.C.B. (Printed Circuit Board) Remove
24
8.4. Adjustment Volume Location
25
8.5. Test Point Location
25
9 Service mode
26
9.1. CAT (computer Aided Test) mode
26
9.2. IIC mode structure (following items value is sample data.)
29
10 Adjustment
30
10.1. RGB white balance adjustment
30
10.2. HD white balance adjustment
32
10.3. Power control adjustment
34
11 Trouble shooting guide
35
11.1. Self Check
35
HD, VD
/
1.0 - 5.0 Vp-p (high impedance)
Component
Y: 1.0 Vp-p (75-ohm : include sync)
P
B
/C
B
: 0.7 Vp-p (75-ohm)
P
R
/
C
R
: 0.7 Vp-p (75-ohm)
A
UDIO IN (M3 JACK) 0.5 Vrms (high impedance)
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN) RS-232C COMPATIBLE
SPEAKERS (6Ω) 16 W [8 W + 8 W] (10 % THD)
Accessories Supplied
Remote Control Transmitter EUR7636070R
Batteries 2×
AA
Size
Fixing bands (TMME203 or TMME187) × 2
Dimensions (
W
×H×D) 47.6” (1,210 mm) × 28.5” (724 mm) × 3.7” (95 mm)
Mass (weight)
main unit onl
y
approx. 81.6 lbs
with speakers approx. 90.4 lbs
Notes:
· Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
· This equipment complies with the EMC standards listed below. EN55022, EN55024, EN61000-3-2, EN61000-3-3. (EK/ES/BK/BS)
CONTENTS
Page Page
2
TH-50PH9UK