LCD Keypad 13
Options [4] and [5]: Arming with Card
Options 4 and 5 de fine the type of arming when arming with a n Access Control Card (refer to section 6.2.1 on page
13). You can eithe r Regular arm, Stay arm, Fo rce arm, or Disable the Ar ming with Car d feature.
[4] ON, [5 ] OFF = Regu lar Arm
[4] OFF, [5] ON = Stay Arm
[4] and [5] ON = Fo rce Arm
[4] and [5] OFF = Disable the Armin g with Card fea ture
Option [6]: A dd Toler ance Windo w to Sched ule
Wh en option [6] is ON, the Sched ule Tolerance Win dow feature i s enab led. This fe ature exte nds a User’s sche duled
access p eriod thro ugh an Access Control Door by the amo unt p rogrammed by your Instal ler. For e xa mple, if the
User ’s assigned sched ule for the door is Mo nday to Frida y fro m 9:00 a.m. to 5 :00 p.m., and your Installer sets the
“Tolerance Wi ndow” a t one hour, the Use r with the “Sched ule Tolerance Wind ow” ena bled will be abl e to enter and
exit one h our before and after the ir scheduled time for that d oor.
Option [7]: Co de Follows Schedu le
Wh en op tion [7] is ON, Users can u se their Access Code s only dur ing their sche dule d hou rs assigned in step 8 in
Fig ure 5.1 on pag e 10. Wh en the option is OFF, Users can use their Access Codes at any time.
Option [8]: Card to Unlock and Code to Disarm
O pt ion [8 ] fu nctio ns o nly if o ption [2 ] in se ct ion 5. 8 is OFF. W he n o pt ion [8 ] is ON, a User can use an Access Control
Card to unlock an armed Access Control Door, however the User must enter a User Access Code to disarm the
armed are a. Whe n option [8] i s OFF, a User can gain access to an Access Control Door on ly if the d oor ’s ar ea(s) is
already disarmed.
For option [8] to function in the ON position, option [5] “Arm Only” in the User Options must
be disabled (refer to section 5.7 on page 12).
6.0 USING ACCESS CONTROL
6.1 ENTERING & EXITING
Depend ing on ho w your system is install ed, the re are vario us ways to en ter a nd exit Access Control Do ors:
1)Present you r Access Con tro l Card to the re ader. The system will verify that the
card is allowe d acce ss accordin g to its assigned Access Le vel a nd Schedule. If it
is accepted, the system will u nlock the doo r. The rea der ’s l ight can be
programmed by the installer to turn gre en or extingu ish briefly to indicate that the
door can be ope ned .
2)Whe n the motion de tector dete cts movement (Requ est for Exit), it will unlock the
door to p ermit passage from inside.
3)Enter you r User Access Code on the keypad and press [
AC C].
4)If the Access Control Door is on a “Door Unlocked Sched ule” , you ma y be ab le to
open Access Control Doors without using a User Access Code or an Access
Control Card. Depending on the do or’s prog ramming, the door can r emain
unlocked du ring the entire pro grammed schedule or the door can unlock once a
valid Access Control Ca rd is pre sented to the rea der d uring th e schedule and
then will rema in unlo cked for the remai nder of the schedule .
6.2 ARMING AND DISARMING WITH CARD
6.2.1 ARMING WITH CARD
An Access Control Card can be progra mmed to a rm area s assigned to the d oor when it is presented to
the read er (doo r) twice with in app roximately 5 secon ds witho ut op enin g the d oor.
To Next Page
Loading...
