Penlon A200SP - Appendix: EMC Information; Electromagnetic Compatibility and Emissions

A200SP Absorber 37 User Manual
Appendix
Appendix 5. Electromagnetic compatibility (EMC)
Electromagnetc envronment
The A200SP Absorber s sutable for use n the specfed electromagnetc envronment
The user of the A200SP Absorber should assure that t s used n an electromagnetc envronment as
descrbed below
hanges or modfcatons to ths anaesthetc machne system, not expressly approved by Penlon Lmted,
could result n EM ssues wth ths absorber ontact Penlon Lmted for more nformaton
The use of phones or RF emttng equpment near ths absorber may cause nterference
Always montor absorber operaton before and durng use on a patent
The essental performance of the A200SP Absorber s to transmt gas mxture to and from a patent Soda
lme, housed n a canster mounted on the absorber, s used to absorb exhaled O
WARNIN
The A200SP Absorber should not be used adacent to or stacked wth other manufacturer’s equpment If
adacent or stacked use s necessary, the absorber should be observed to verfy normal operaton n the
confguraton n whch t wll be used
ables, Transducers, and Accessores
WARNIN
The A200SP Absorber s EM-complant wth all cables, transducers and accessores suppled by Penlon
Lmted
The use of cables, transducers and accessores other than those specfed may result n ncreased
emssons or decreased mmunty of the A200SP Absorber
The use of cables, transducers and accessores suppled by Penlon Lmted on non-Penlon equpment
may also result n ncreased emssons or decreased mmunty of that equpment
Cables supplied by Penlon Limited
Category
Function Length (m)
A lnk Prma 450/460 to A200SP absorber Mains supply for an A200SP absorber equipped
with a heater.
0.6
A200SP control cable (A200SP Absorber ftted to a
Prma 450/460 equpped wth an AV-S ventlator)
Connects (a) the spirometry sensors and (b)
the absorber bag/vent switch on the A200SP
absorber to the AV-S ventilator
0.8
Oxygen sensor cable (A200SP Absorber ftted to a
Prma 450/460 equpped wth an AV-S ventlator)
Connects the oxygen sensor on the A200SP
absorber to the AV-S ventilator
2.7
Guidance and manufacturer’s declaration – electromagnetic emissions
The A200SP Absorber s ntended for use n the electromagnetc envronment specfed below The customer or user should
assure that t s used n such an envronment
Required test Compliance omments
ERF emssons
ISPR 11
Group 1
Class A
lass A equpment s sutable for use n all locatons other than those allocated
n resdental envronments and those drectly connected to a low voltage power
supply network whch supples buldngs used for domestc purposes, and may
be used n domestc establshments and those drectly connected to the publc
low-voltage power supply network that supples buldngs used for domestc
purposes provded the followng warnng s heeded
NOTE The EMISSIONS characterstcs of ths equpment make t sutable
for use n ndustral areas and hosptals (ISPR 11 class A) If t s used n a
resdental envronment (for whch ISPR 11 class B s normally requred)
ths equpment mght not offer adequate protecton to rado-frequency
communcaton servces The user mght need to take mtgaton measures,
such as relocatng or re-orentng the equpment
Harmonc emssons
IE 61000-3-2
Complies
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Complies