ROEL CERBER C52 - Simultaneous Erasure of All User Codes (Except Master); Programming;Erasing Follow Me Phone Numbers

26
5. Erasure of „selected user code” (except the „master code”) can be performed by
entering of [*] key (instead of sequence of 4 digits) while the control panel just entered the
programming/erasing session of the corresponding „selected user code”. The keypad buzzer
will sound 6 confirmation beeps and the control panel will go back within „master user’s
programming menu”.
Notes:
1. All rights are enabled by default for the master code.
2. Only “zone bypassing”, “regular arming” and “access to partition A” rights are enabled by default for the
other 01 to 30 user codes.
3. The „master code” erasing isn’t allowed. If, by mistake, one is trying to erase the master code, by entering
[*] key instead of the 4-digits code, the keypad buzzer will sound a long rejection beep and the panel will go
back within „master user’s programming menu” and will keep the old value for the „master code”.
Any user code from 01 to 30 can be selected in order to get a new value or press [#] key to
exit the master user’s programming menu.
SIMULTANEOUS ERASURE OF ALL USERS' CODES (EXCEPT THE „MASTER CODE”)
[*][7][Master Code][49] or [CODE][Master Code][49],
where [CODE] is the key labeled “CODE”
While the system is within „master user’s programming menu”, to simultaneous erase all
user codes (except the „master code”), select the corresponding submenu [49], by
entering the [4] and [9] keys.
The keypad buzzer will sound 3 confirmation beeps and the control panel will go back into
master user’s programming menu.
Any user code from 01 to 30 can be selected in order to get a new value or press [#] key to
exit the master user’s programming menu.
PROGRAMMING / SELECTIVE ERASURE OF THE 1 TO 4 FOLLOW ME PHONE NUMBERS
[*][7][Master Code][5X][Phone number X][#] or [CODE][Master Code][5X][Phone
number X][#],
where [CODE] is the key labeled “CODE” and „X” is the 1 to 4 order number for the 4 follow me phone numbers, which
can be programmed by the master in this submenus.
The [*][7][Master Code][5X][Phone number X][#] or [CODE][Master Code][5X][Phone
number X][#] commands allow to the „master user” to program / selective erase the follow
me phone numbers.
Notes:
1. The “follow me phone numbers” denomination will be used for the phone numbers which the control panel
will automatic dial upon occurring in the system of alarms and „AC power loss” event, to report these events
and the system status too, by synthesis sounds.
2. Up to 4 follow me phone numbers can be programmed by the master user for the control panel to automatic
report on the phone line the alarms and „AC power loss” event, by specific synthesis sounds.
While the system is within „master user’s programming menu”, in order to program /
erase any of the 1 to 4 follow me phone numbers, select the corresponding
submenu from [51] to [54], by entering one of the groups [51], [52], [53] or [54]
(enter [51] to select the 1
-st
follow me phone number, [52] for the 2
-nd
one and so on).
While the system is within programming session of the selected phone number, the keypad LEDs’ status will
be as follows:
Remarks:
ARMED A LED
ON
SYSTEM LED
Blinking
READY A LED
ON
Zone 1, 2 and 3 LEDs
Blinking
Means the selected phone number was programmed during a previous
programming session and the control panel is waiting for the first digit entering.
Only zone 1 LED
Blinking
Means the selected phone number isn’t programmed and the control panel is
waiting for the first digit entering.
Zone 1 and 2 LEDs
Blinking
Means the selected phone number is programming
1. Programming / Erasing of the selected phone number can be canceled by
pressing the [#] key. After [#] key pressing, the keypad buzzer will sound 6 confirmation
beeps and the control panel will go back within „master user’s programming menu”.