EasyManuals Logo
Home>Roland>Recording Equipment>Octa-Capture

Roland Octa-Capture User Manual

Roland Octa-Capture
100 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #99 background imageLoading...
Page #99 background image
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
BROWN:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
NEUTRAL
LIVE
For the U.K.
This product complies with the requirements of EMC Directive 2004/108/EC.
For EU Countries
For Canada
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
NOTICE
AVIS
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US
(
Proposition 65
)
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
UA-5
USB Audio Interface
Edirol Corporation North America
425 Sequoia Drive, Suite 114, Bellingham, WA 98226
(360) 594-4276

Table of Contents

Other manuals for Roland Octa-Capture

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roland Octa-Capture and is the answer not in the manual?

Roland Octa-Capture Specifications

Audio Channels IconAudio Channels
number of audio record channels (44.1/48/96 kHz)12 channels
number of audio playback channels (44.1/48/96 kHz)10 channels
number of audio record channels (192 kHz)4 channels
number of audio playback channels (192 kHz)4 channels
Signal Processing IconSignal Processing
pc interface bit depth24-bit
ad/da conversion bit depth24-bit
internal processing bit depth40-bit
Sampling Frequency IconSampling Frequency
ad/da conversion sampling frequency44.1/48/96/192 kHz
digital (in/out) sampling frequency44.1/48/96 kHz
Input and Output Levels IconInput and Output Levels
nominal input level (input jack 1-6, xlr type)-56 to -6 dBu
nominal input level (input jack 7-8, xlr type)-50 to +0 dBu
nominal input level (input jack 1-8, 1/4-inch trs phone type)-46 to +4 dBu
nominal output level (output 1-8)+0 dBu (balanced)
headroom16 dB
Impedance IconImpedance
input impedance (input jack 1-6, xlr type)5 k ohms (balanced)
input impedance (input jack 7-8, xlr type)10 k ohms (balanced)
input impedance (input jack 1-8, 1/4-inch trs phone type)17 k ohms (balanced)
output impedance (output 1-8)1.8 k ohms (balanced)
output impedance (phones)47 ohms
Frequency and Noise IconFrequency and Noise
frequency response (192 kHz)20 Hz to 90 kHz (+0/-8 dB)
frequency response (96 kHz)20 Hz to 40 kHz (+0/-2 dB)
frequency response (48 kHz)20 Hz to 22 kHz (+0/-2 dB)
frequency response (44.1 kHz)20 Hz to 20 kHz (+0/-2 dB)
residual noise level-87 dBu typ. (GAIN: min., 600 ohms terminated, IHF-A)
Dynamic Range and Display IconDynamic Range and Display
dynamic range (ad block input 1-8)104 dB typ. (GAIN: min.)
dynamic range (da block output 1-8)113 dB typ.
display128 x 64 dots Graphic LCD (backlit LCD)
Connectors IconConnectors
input jacks (xlr type / 1/4-inch trs phone type)XLR type (balanced/phantom power +48 V), 1/4-inch TRS phone type (balanced)
coaxial input connectorpresent
coaxial output connectorpresent
headphone jackStereo 1/4-inch phone type
output jack (1/4-inch trs phone type)balanced
midi connectorsIn, Out
usb connectorpresent
Power and Dimensions IconPower and Dimensions
power supplyDC 9 V (AC adaptor)
current draw1.45 A
dimensions283.8 (W) x 157.9 (D) x 50.4 (H) mm / 11-3/16 (W) x 6-1/4 (D) x 2 (H) inches
weight1.32 kg / 2 lbs 15 oz

Related product manuals