71
Effects
RT H Slow (RT High Frequency Slow Rate)
0.05–10.0 [12 (40 03 0E)]
Adjusts the speed of the high-range rotor for the slow-
speed setting.
RT H Fast (RT High Frequency Fast Rate)
0.05–10.0 [13 (40 03 0F)]
Adjusts the speed of the high-range rotor for the fast-speed
setting.
RT Hi Accl (RT High Frequency Acceleration)
0–15 [14 (40 03 10)]
Adjusts the time over which the rotation speed of the high-
range rotor will change from slow-speed to fast-speed (or
fast-speed to slow-speed) rotation. Smaller values will
require greater time to reach the new rotational speed.
RT Hi Lev (RT High Frequency Level)
0–127 [15 (40 03 11)]
Adjusts the volume of the high-range rotor.
RT Sept (RT Separation) 0–127 [16 (40 03 12)]
Adjusts the spatial spread of the rotary sound.
#RT Speed Slow/Fast [17 (40 03 13)]
Simultaneously switch the rotational speed of both the low-
range and the high-range rotors.
Slow: Slow down the rotation to the specified
speeds (RT L Slow parameter/RT H Slow
parameter values).
Fast: Speed up the rotation to the specified speeds
(RT L Fast parameter/RT H Fast parameter
values).
Level (Output Level) 0–127 [20 (40 03 16)]
Adjusts the output level.
48: GTR Multi 1 (Guitar Multi 1) [04H, 00H]
Guitar Multi 1 connects Compressor (Cmp), Overdrive or
Distortion (OD), Chorus or Flanger (CF), and Delay (Dly)
effects in series.
fig.9-51
● Cmp (Compressor)
Cmp Atck (Compressor Attack) 0–127 [1 (40 03 03)]
Adjusts the time over which the sound will rise after input.
Cmp Sus (Compressor Sustain) 0–127 [2 (40 03 04)]
Adjusts the time over which low-level sounds are boosted
until they reach a specified volume.
Increasing the value will shorten the time. When the value
is modified, the level will also change.
Cmp Level (Compressor Level) 0–127 [3 (40 03 05)]
Adjusts the volume of the compressor sound.
Cmp Sw (Compressor Switch) Off/On [4 (40 03 06)]
Turns the compressor on/off.
● OD (Overdrive/Distortion)
OD Sel (OD Select) Odrv/Dist [5 (40 03 07)]
Selects either Overdrive or Distortion.
+OD Drive 0–127 [6 (40 03 08)]
Adjusts the depth of distortion. The volume will change
together with the depth of distortion.
OD Amp (OD Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [7 (40 03 09)]
Selects the type of guitar amp.
Small: small amp
BltIn: single-unit type amp
2-Stk: large double stack amp
3-Stk: large triple stack amp
OD Amp Sw (OD Amp Switch) Off/On [8 (40 03 0A)]
Turns OD Amp on/off.
OD L Gain (OD Low Gain) -12–+12 [9 (40 03 0B)]
Adjusts the low-range gain.
OD H Gain (OD High Gain) -12–+12 [10 (40 03 0C)]
Adjusts the high-range gain.
OD Sw (OD Switch) Off/On [11 (40 03 0D)]
Turns Overdrive or Distortion on/off.
● CF (Chorus/Flanger)
CF Sel (CF Select) Chorus/Flangr [12 (40 03 0E)]
Selects either Chorus or Flanger.
CF Rate 0.05–6.40 [13 (40 03 0F)]
Adjusts the speed of modulation
CF Depth 0–127 [14 (40 03 10)]
Adjusts the depth of modulation.
CF Fb (CF Feedback) -98%–+98% [15 (40 03 11)]
Adjusts the amount (%) of the flanger sound that is
returned to the input. Negative (-) values will invert the
phase.
* In the case of Chorus, this will have no effect.
CF Mix 0–127 [16 (40 03 12)]
Adjusts the volume of the chorus or flanger sound.
● Dly (Delay)
Dly Time (Delay Time) 0–635ms [17 (40 03 13)]
Adjusts the time from the original sound until when the
delay sound is heard.
Dly Fb (Delay Feedback Level) 0–127 [18 (40 03 14)]
Adjusts the amount of the delay sound that is returned to
the input.
#Dly Mix (Delay Mix) 0–127 [19 (40 03 15)]
Adjusts the volume of the delay sound.
Level (Output Level) 0–127 [20 (40 03 16)]
Adjusts the output level.
L
R
DelayCmp
CF
OD
To Next Page
Loading...
Need help?
General
