25
Editing a Kit’s Settings (KIT Edit)
Parameter Value Explanation
HP Level
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the HPF level of the filter.
BP Level
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the BPF level of the filter.
LP Level
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the LPF level of the filter.
Bypass
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the bypass level.
COMPRESSOR
Balance
MASTER FX
[CTRL] *1
OFF, 1–255
Adjusts the compression effect.
With a setting of 255, the compression
effect is at 100%.
Attack
MASTER FX
[CTRL] *1
0–255
Specifies the time from the moment
that the input exceeds the level
specified by Thre until the volume
starts being compressed.
As the Attack is increased (lengthening
the time), the beginning of the note
will no longer be compressed.
Release
MASTER FX
[CTRL] *1
0–255
Specifies the time from the moment
that the input falls below the level
specified by Thre until compression
stops being applied.
As the Release is increased
(lengthening the time), the sound will
have more sustain.
Thre -40dB–0dB
Specifies the level at which
compression begins.
Set a lower value for Thre if you want
to apply compression deeply, or if the
input level is low.
Because setting a low value for Thre
also lowers the output level, raise Gain
to make adjustments.
Gain
-40dB–0dB–
+40dB
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
Ratio
1: 1.00, 1: 1.12,
1: 1.25, 1: 1.40,
1: 1.60, 1: 1.80,
1: 2.00, 1: 2.50,
1: 3.20, 1: 4.00,
1: 5.60, 1: 8.00,
1: 16.0, 1: INF
Specifies the compression ratio.
The higher the ratio, the more
compression is applied to the sound
when its level exceeds the Thre
setting.
If the ratio is set to 1: INF, the sound
will not become any louder than the
level specified by Thre.
Knee
HARD, SOFT1,
SOFT2, SOFT3,
SOFT4, SOFT5,
SOFT6, SOFT7,
SOFT8, SOFT9
Adjusts the character of the
compression.
HARD compresses the sound
suddenly, producing a hard sound.
SOFT compresses the sound gently,
producing a soft sound.
DRIVE
Balance
MASTER FX
[CTRL] *1
OFF, 1–255
Adjusts the drive effect.
With a setting of 255, the drive effect
is at 100%.
Drive
MASTER FX
[CTRL] *1
0–255
Adjusts the depth of distortion.
Because increasing the Drive setting
also increases the output level, make
adjustments by lowering the Level
setting.
Level
MASTER FX
[CTRL] *1
0–255
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
Parameter Value Explanation
HpFreq
MASTER FX
[CTRL] *1
0–255
Specifies the frequency below which
the low-frequency region of the input
is cut.
As the HpFreq is raised, the region
being cut will extend further into the
high-frequency region.
PreEqFreq
MASTER FX
[CTRL] *1
0–255
Specifies the center frequency of the
EQ that is applied before distorting
the sound.
PreEqL
MASTER FX
[CTRL] *1
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the low-frequency level of
the EQ that is applied before distorting
the sound.
PreEqH
MASTER FX
[CTRL] *1
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the high-frequency level of
the EQ that is applied before distorting
the sound.
By slightly decreasing the high-
frequency level, you can reduce
the higher-order partials that are
generated by distortion.
PostEqFreq
MASTER FX
[CTRL] *1
0–255
Specifies the center frequency of the
EQ that is applied after distorting the
sound.
PostEqL
MASTER FX
[CTRL] *1
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the low-frequency level of
the EQ that is applied after distorting
the sound.
PostEqH
MASTER FX
[CTRL] *1
-INF, -53.0dB–
0.0dB–+10.0dB
Specifies the high-frequency level of
the EQ that is applied after distorting
the sound.
OVERDRIVE
Balance
MASTER FX
[CTRL] *1
OFF, 1–255
Adjusts the overdrive effect.
With a setting of 255, the overdrive
effect is at 100%.
Drive
MASTER FX
[CTRL] *1
0–255
Adjusts the depth of distortion.
Because increasing Drive also
increases the output level, make
adjustments by lowering Level.
Tone
MASTER FX
[CTRL] *1
0–255
Adjusts the tone.
Raising the Tone emphasizes the high-
frequency region.
Lowering the Tone emphasizes the
low-frequency region.
Level
MASTER FX
[CTRL] *1
0–255
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
DISTORTION
Balance
MASTER FX
[CTRL] *1
OFF, 1–255
Adjusts the distortion effect.
With a setting of 255, the distortion
effect is at 100%.
Drive
MASTER FX
[CTRL] *1
0–255
Adjusts the depth of distortion.
Because increasing Drive also
increases the output level, make
adjustments by lowering Level.
Tone
MASTER FX
[CTRL] *1
0–255
Adjusts the tone.
Raising the Tone emphasizes the high-
frequency region.
Lowering the Tone emphasizes the
low-frequency region.
Level
MASTER FX
[CTRL] *1
0–255
Specifies the output level.
Set this so that the volume is
essentially the same whether the
MASTER FX Sw is on or off.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
