Sanyo PLC-WXU700 - Page 49

48
Setting
Note:
 •Auto Keystonecorrectsverticaldistortiononly,not
correcthorizontaldistortion.
 •The
Auto Keystonefunctioncannotworkwhenthe
CeilingfeatureissetOnintheSettingmenu(p.53).
 •Perfectcorrectionoftheimagedistortioncannot
beensuredwiththeAutosetupfunction.Ifthe
distortionisnotcorrectedproperlybypressingthe
AUTOSETUP/CANCELbutton,adjustmanually
bypressingtheKEYSTONEbuttonontheremote
controlorselecting
KeystoneintheSettingmenu
(pp.26,49).
 •Fine sync,Total dots,HorizontalandVertical
positionofsomecomputerscannotbefullyadjusted
withtheAutoPCadjustmentfunction.Whenthe
imageisnotprovidedproperlywiththisoperation,
manualadjustmentsarerequired(pp.34-35).
Auto setup
Input search
Thisfunctiondetectstheinputsignalautomatically.When
asignalisfound,thesearchwillstop.UsethePoint▲▼
buttonstoselectoneofthefollowingoptions.
Off......Inputsearchwillnotwork.
On1.... Inputsearchworksunderthefollowingsituation.
 –WhenpressingtheAUTOSETUP/CANCEL
buttononthetopcontrol.
 –WhenpressingtheAUTOSET/CANCELbutton
ontheremotecontrol.
On2.... Inputsearchworksunderthefollowingsituation.
 –Whenturningontheprojectorbypressingthe
ON/STAND-BYbuttononthetopcontrolorthe
remotecontrol.
 –WhenpressingtheAUTOSET/CANCELbutton
ontheremotecontrol.
 –WhenpressingtheAUTOSETUP
/CANCEL
buttononthetopcontrol.
 –Whenthecurrentinputsignaliscutoff.*
*IftheNoshoworFreezefunctionisactive,cancelitto
activatetheInputsearch.ItisalsounavailablewhenOn-
Screenmenuisdisplayed.
Auto PC adj.
On . . . . . . EnablesAutoPCadjustmentwhenpressing
theAUTOSET/CANCELbuttonontheremote
controlortheAUTOSETUP/CANCELbutton
onthetopcontrol.
Off . . . . . .DisablesAutoPCadjustment.
Auto Keystone
Auto. . . . Alwaysworksandcorrectskeystone
distortionaccordingtotheprojector'stilt.
Manual . . WorksonlywhenpressingtheAUTOSETUP/
CANCELbuttononthetopcontrolorthe
AUTOSET/CANCELbuttonontheremote
control.
Off . . . . . .DisablesAutoKeystone.
HDMI setup
Terminal Computer 2
Pointer Dot
Standby mode Eco
Auto setup
Note:
•WhileInput searchissettoOn1orOn2,thestatusofInput
andLamparedisplayedeverytimethesignalisswitched.
•Onlythelastselectedinputsourcecanbedetected.
•IftheINPUTbuttononthetopcontrolortheHDMI,
COMPUTER,VIDEOorNETWORKbuttonsontheremote
controlispressedduringInputsearchisinprogress,Input
searchwillstopandgobacktothepreviousinputsignal.
 •Input search, Auto PC adj. and Auto Keystone cannot be
set
Offatthesametime.
ThisfunctionenablesInputsearch,AutoKeystonecorrection
andAutoPCadjustmentbypressingtheAUTOSETUP/
CANCELbuttononthetopcontrolortheAUTOSET/CANCEL
buttonontheremotecontrol.Settingsforthosefunctionscan
bealteredasfollows: