Sartorius Master series

To Next Page

To Previous Page

LC 2201S, LC 2201P, LC 821(-0CE)

LC 421, GC 1201-G

Note: All dimensions are given in millimeters.

6–26

Main Page

Table of Contents2
Warranty10
Storage and Shipping Condtions10
Installation Instructions11
Getting Started13
- Connecting the Balance to AC Power14
- Connecting Electronic Devices (Peripherals)15
- Safety Precautions15
- Voltage Selection15
- Adjusting the Display Unit16
- Information on Radio Frequency Interference16
- Information on Weighing Electrostatically Charged Samples16
- Leveling the Balance Using the Level Indicator17
Operating the Balance18
- Warmup Time18
- Turning the Display on and off18
- Self-Test18
- Taring20
- Weighing20
- Weighing Range Structure21
Weighing in the IQ-Mode (Load-Dependent Readability)22
Calibration23
- Sensitivity Test27
Data Interface29
Below-Balance Weighing31
Fastening an Antitheft Locking Device31
Troubleshooting Guide32
Care and Maintenance34
Manufacturer's Declaration36
Balance Operating Menu37
- Changing a Menu Code Setting38
- Undoing All Menu Code Changes: Reset Function40
Balance Operating Parameters41
- Adapting the Balance to Ambient Conditions41
- Standard Weighing Mode - Manual Filling Mode41
- Stability Range41
- Stability Symbol Delay42
- Tare Parameter42
- Auto Zero Function42
Weighing in Three Ranges on Standard Balances43
- Selecting the Number of Ranges43
- Weight Units43
Weighing in Two Ranges on Verified Balances45
- Selecting the Number of Ranges45
- Weight Units45
Display Modes on Standard Balances46
- Final Readout Mode46
- Last Numeral Blanked When the Load Changes46
- Round-Off Function46
- IQ-Mode46
- Polyrange Function47
Display Modes on Verified Balances48
Calibration Functions on Standard Balances49
Calibration Functions on Verified Balances50
Utilities for Printouts or Data Transfer51
- Data Output Parameter51
- Automatic Data Output51
- Data Output at Defined Intervals52
- Automatic Taring after Data Output52
- Data ID Codes53
Additional Functions54
- Menu Access Function on Standard Balances54
- Beep Tone (Acoustic Signal)54
- Blocking the Keys54
- Universal Switch for Remote Control55
- Analog Display: Bar Graph/Marker55
- Power-On Mode55
- Automatic Shutoff (Battery Saver)56
- Display Backlighting56
Isocal" Self-Calibrating Function on AC/LC57
Range of Performance Features57
Isocal" Self-Calibrating Function58
- Flashing W Symbol58
- Activating Internal Calibration Manually59
- Automated Processes60
- Printout or Record of Calibration Processes60
- Calibrating Balances When Using YDK 01, YWP 01, YWP 01 U60
- Or YWP 02 Accessories60
- Interface (Binary Converter)60
Application Programs for Balances of the Product Line61
Functions Common to All Programs62
Tare Memory64
- Display/Print Tare - Net - Gross Weights64
- Net Total65
Weighing in Percent66
- Determination of the Residual Weight in Percent66
- Sieve Analysis67
Over/Under Checkweighing69
- Checking Net Weights70
- Checking Variations in Weight71
Counting73
Interface Description75
General Specifications75
Data Output Formats76
Data Input Formats80
- Table of ASCII Characters83
Synchronization and Data Output Parameters84
Settings for the Interface Parameters87
Control Lines88
Pin Assignment Chart89
Cabling Diagram90
Product Data Sheets91
Specifications98
Dimensions (Scale Drawings)105
Accessories (Options)109
Declarations of Conformity113
EC Verification" - a Service116
New Installation" - a Service116
- Subsequent Verifications Within the European Union116
- Sartorius European Service Center Addresses117
To Directive No. 90/384/EEC118
Declaration of Conformity to Directive 89/336/EEC120
Brief Instructions121

Sartorius Master series - Page 107

Table of Contents

Related product manuals